Difficulty

Difficult

Steps

28

Time Required

                          1 hour

Sections

8

  • Lower Case
  • 2 steps
  • Battery
  • 1 step
  • Solid-State Drive
  • 2 steps
  • I/O Board Cable
  • 3 steps
  • Fan
  • 3 steps
  • Battery
  • 2 steps
  • Logic Board
  • 11 steps
  • Logic Board
  • 4 steps

Flags

0

  • BackMacBook Air 11" Mid 2011

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Lower Case
  • Shut down and close your computer. Lay it on a soft surface top-side down.
  • Remove the following ten screws:
  • Two 8 mm 5-point Pentalobe screws
  • Eight 2.5 mm 5-point Pentalobe screws
  • The special screwdriver needed to remove the 5-point Pentalobe screws can be found here.

Shut down and close your computer. Lay it on a soft surface top-side down.

Remove the following ten screws:

Two 8 mm 5-point Pentalobe screws

Eight 2.5 mm 5-point Pentalobe screws

The special screwdriver needed to remove the 5-point Pentalobe screws can be found here.

1024

Step 2

  • Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.

Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.

Step 3

              Battery
  • In this step you will disconnect the battery to help avoid shorting out any components during service.
  • Use the flat end of a spudger to pry both short sides of the battery connector upward to disconnect it from its socket on the logic board.
  • Bend the battery cable slightly away from the logic board so the connector will not accidentally contact its socket.

In this step you will disconnect the battery to help avoid shorting out any components during service.

Use the flat end of a spudger to pry both short sides of the battery connector upward to disconnect it from its socket on the logic board.

Bend the battery cable slightly away from the logic board so the connector will not accidentally contact its socket.

Step 4

              Solid-State Drive
  • Remove the single 2.9 mm T5 Torx screw securing the SSD to the logic board.

Remove the single 2.9 mm T5 Torx screw securing the SSD to the logic board.

Step 5

  • Use a spudger to help lift the free end of the SSD just enough to grab it with your other hand.
  • Do not lift the end of the SSD excessively.
  • Pull the drive straight out of its socket and remove it from the logic board.
  • When reinstalling the SSD, be sure it is properly seated before reinstalling its retaining screw.

Use a spudger to help lift the free end of the SSD just enough to grab it with your other hand.

Do not lift the end of the SSD excessively.

Pull the drive straight out of its socket and remove it from the logic board.

When reinstalling the SSD, be sure it is properly seated before reinstalling its retaining screw.

Step 6

              I/O Board Cable
  • Use the flat end of a spudger to pry the I/O board cable up from its socket on the I/O board.

Use the flat end of a spudger to pry the I/O board cable up from its socket on the I/O board.

Step 7

  • Peel the I/O board cable up from the adhesive securing it to the fan.

Peel the I/O board cable up from the adhesive securing it to the fan.

Step 8

  • Use the flat end of a spudger to lift the I/O board connector up and out of its socket on the logic board
  • Be sure to lift straight up on the connector as you disconnect it from its socket. The socket is very deep on the logic board and prying it from side to side may damage the logic board
  • Remove the I/O board cable.

Use the flat end of a spudger to lift the I/O board connector up and out of its socket on the logic board

Be sure to lift straight up on the connector as you disconnect it from its socket. The socket is very deep on the logic board and prying it from side to side may damage the logic board

Remove the I/O board cable.

Step 9

              Fan
  • Use the tip of a spudger to carefully flip up the retaining flap on the fan cable ZIF socket.
  • Be sure you are prying up on the hinged retaining flap, not the socket itself.

Use the tip of a spudger to carefully flip up the retaining flap on the fan cable ZIF socket.

Be sure you are prying up on the hinged retaining flap, not the socket itself.

Step 10

  • Remove the following three screws securing the fan to the upper case:
  • Two 5.2 mm T5 Torx screws
  • One 3.6 mm T5 Torx screw

Remove the following three screws securing the fan to the upper case:

Two 5.2 mm T5 Torx screws

One 3.6 mm T5 Torx screw

Step 11

  • Lift the fan out of the upper case and carefully pull the fan ribbon cable out of its socket as you remove it from the Air.

Lift the fan out of the upper case and carefully pull the fan ribbon cable out of its socket as you remove it from the Air.

Step 12

              Battery
  • Remove the following five screws securing the battery to the upper case:
  • Two 5.2 mm T5 Torx screws
  • One 6 mm T5 Torx screw
  • Two 2.6 mm T5 Torx screws

Remove the following five screws securing the battery to the upper case:

One 6 mm T5 Torx screw

Two 2.6 mm T5 Torx screws

Step 13

  • Do not touch or squeeze the six lithium polymer cells when handling the battery.
  • Lift the battery from its edge nearest the logic board and remove it from the upper case.

Do not touch or squeeze the six lithium polymer cells when handling the battery.

Lift the battery from its edge nearest the logic board and remove it from the upper case.

Step 14

              Logic Board
  • Use the flat end of a spudger to free the adhesive loop securing the I/O board power cable to the upper case.
  • Disconnect the I/O board by pulling the power cable away from its socket on the logic board.
  • Pull the cable parallel to the face of the logic board toward the front edge of the Air.

Use the flat end of a spudger to free the adhesive loop securing the I/O board power cable to the upper case.

Disconnect the I/O board by pulling the power cable away from its socket on the logic board.

Pull the cable parallel to the face of the logic board toward the front edge of the Air.

Step 15

  • Use the tip of a spudger to flip up the retaining flap on the keyboard backlight ribbon cable ZIF socket.
  • Be sure you are prying up on the hinged retaining flap, not the socket itself.
  • Pull the keyboard backlight ribbon cable out of its socket.

Use the tip of a spudger to flip up the retaining flap on the keyboard backlight ribbon cable ZIF socket.

Pull the keyboard backlight ribbon cable out of its socket.

Step 16

  • Use the tip of a spudger or your fingernail to flip up the retaining flap on the trackpad ribbon cable ZIF socket.
  • Be sure you are prying up on the hinged retaining flap, not the socket itself.
  • Pull the trackpad ribbon cable straight out of its socket toward the front edge of the Air.

Use the tip of a spudger or your fingernail to flip up the retaining flap on the trackpad ribbon cable ZIF socket.

Pull the trackpad ribbon cable straight out of its socket toward the front edge of the Air.

Step 17

  • Use the tip of a spudger to de-route the right speaker cable from the slot cut into the logic board.

Use the tip of a spudger to de-route the right speaker cable from the slot cut into the logic board.

Step 18

  • Use the flat end of a spudger to pry the right speaker cable connector up and out of its socket on the logic board.
  • Pry up from beneath the cables.

Use the flat end of a spudger to pry the right speaker cable connector up and out of its socket on the logic board.

Pry up from beneath the cables.

Step 19

  • Gently push the tip of a spudger under the black plastic flap stuck to the display data cable lock to make the lock pop upward and away from the socket.
  • Remove the small rubber gasket from the corner of the upper case near the display data cable.

Gently push the tip of a spudger under the black plastic flap stuck to the display data cable lock to make the lock pop upward and away from the socket.

Remove the small rubber gasket from the corner of the upper case near the display data cable.

Step 20

  • While holding the lock away from the socket, gently pull the display data cable out of its socket.
  • Do not pull upward on the display data cable as you disconnect it, as its socket may break off the logic board.

While holding the lock away from the socket, gently pull the display data cable out of its socket.

Do not pull upward on the display data cable as you disconnect it, as its socket may break off the logic board.

Step 21

  • Use the flat end of a spudger to pry both antenna cable connectors up and off their sockets on the AirPort/Bluetooth card.

Use the flat end of a spudger to pry both antenna cable connectors up and off their sockets on the AirPort/Bluetooth card.

Step 22

  • Gently de-route the antenna cables from the slot cut into the logic board.

Gently de-route the antenna cables from the slot cut into the logic board.

Step 23

  • Remove the three 3.6 mm T5 Torx screws securing the logic board to the upper case.

Remove the three 3.6 mm T5 Torx screws securing the logic board to the upper case.

Step 24

  • Gently lift the logic board assembly out of the upper case, minding the fragile heat sink and any cables that may get caught.

Gently lift the logic board assembly out of the upper case, minding the fragile heat sink and any cables that may get caught.

Step 25

              Logic Board
  • Remove the single 2.9 mm T5 Torx screw securing the AirPort/Bluetooth card to the logic board.

Remove the single 2.9 mm T5 Torx screw securing the AirPort/Bluetooth card to the logic board.

Step 26

  • Slightly lift the free end of the AirPort/Bluetooth board and pull it out of its socket on the logic board.
  • To avoid damaging its socket on the logic board, do not excessively lift the free end of the AirPort/Bluetooth card.
  • Remove the AirPort/Bluetooth board from the logic board.

Slightly lift the free end of the AirPort/Bluetooth board and pull it out of its socket on the logic board.

To avoid damaging its socket on the logic board, do not excessively lift the free end of the AirPort/Bluetooth card.

Remove the AirPort/Bluetooth board from the logic board.

Step 27

  • Remove the four 2.5 mm T5 Torx screws securing the heat sink to the logic board.

Remove the four 2.5 mm T5 Torx screws securing the heat sink to the logic board.

Step 28

  • If the heat sink seems to be stuck to the logic board after removing all four screws, use a spudger to carefully separate the heat sink from the faces of the CPU and GPU.
  • Remove the heat sink from the logic board.
  • Logic board remains.
  • When reinstalling the heat sink, be sure to apply a new layer of thermal paste. If you have never applied thermal paste before, we have a guide that makes it easy.

If the heat sink seems to be stuck to the logic board after removing all four screws, use a spudger to carefully separate the heat sink from the faces of the CPU and GPU.

Remove the heat sink from the logic board.

Logic board remains.

When reinstalling the heat sink, be sure to apply a new layer of thermal paste. If you have never applied thermal paste before, we have a guide that makes it easy.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      40 other people completed this guide.

Author

                                      with 5 other contributors 


                    Walter Galan

682,038 Reputation

                                      1,203 Guides authored                  



                       Badges:
                       54







                                                        +51 more badges

David - Mar 6, 2018

Reply

Mark Waddington - Aug 14, 2018

Reply

Not sure if this is the right place for this. If I have the 1.6hz logic board can I easily replace with the 1.8hz logic board?

Agustin Orol - Jul 30, 2019

Reply

What size the should the packaging for the LB be? I am considering international shipping. Thanx

Joachim Blum - Apr 17, 2022

Reply

Sehr gute Anleitung, vielen Dank!