Macbook Air 11 Late 2010 Left Speaker Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

Suggest a time??

Sections

Lower Case
2 steps
Battery
3 steps
Left Speaker
5 steps

Flags

BackMacBook Air 11" Late 2010
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Lower Case

Before proceeding, close your computer and lay it on a soft surface top-side down.
Remove the following ten screws:
Two 8 mm 5-point Pentalobe screws
Eight 2.5 mm 5-point Pentalobe screws
The special screwdriver needed to remove the eight 5-point Pentalobe screws can be found here.

Before proceeding, close your computer and lay it on a soft surface top-side down.

Remove the following ten screws:

Two 8 mm 5-point Pentalobe screws

Eight 2.5 mm 5-point Pentalobe screws

The special screwdriver needed to remove the eight 5-point Pentalobe screws can be found here.

1024

Step 2

Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.
Remove the lower case and set it aside.

Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.

Remove the lower case and set it aside.

Step 3

              Battery

Use the flat end of a spudger to pry both short sides of the battery connector upward to disconnect it from its socket on the logic board.
Bend the battery cable slightly away from the logic board so the connector will not accidentally contact its socket.

Use the flat end of a spudger to pry both short sides of the battery connector upward to disconnect it from its socket on the logic board.

Bend the battery cable slightly away from the logic board so the connector will not accidentally contact its socket.

Step 4

Remove the following five screws securing the battery to the upper case:
Two 5.2 mm T5 Torx screws
One 6 mm T5 Torx screw
Two 2.6 mm T5 Torx screws

Remove the following five screws securing the battery to the upper case:

Two 5.2 mm T5 Torx screws

One 6 mm T5 Torx screw

Two 2.6 mm T5 Torx screws

Step 5

When handling the battery, avoid squeezing or touching the six exposed lithium polymer cells.
Lift the battery from its edge nearest the logic board and remove it from the upper case.
If you’re installing a new battery, you should calibrate it after installation:
Charge it to 100%, and then keep charging it for at least 2 more hours. Next, unplug and use it normally to drain the battery. When you see the low battery warning, save your work, and keep your laptop on until it goes to sleep due to low battery. Wait at least 5 hours, then charge your laptop uninterrupted to 100%.
If you notice any unusual behavior or problems after installing your new battery, you may need to reset your MacBook’s SMC.

When handling the battery, avoid squeezing or touching the six exposed lithium polymer cells.

Lift the battery from its edge nearest the logic board and remove it from the upper case.

If you’re installing a new battery, you should calibrate it after installation:

Charge it to 100%, and then keep charging it for at least 2 more hours. Next, unplug and use it normally to drain the battery. When you see the low battery warning, save your work, and keep your laptop on until it goes to sleep due to low battery. Wait at least 5 hours, then charge your laptop uninterrupted to 100%.

If you notice any unusual behavior or problems after installing your new battery, you may need to reset your MacBook’s SMC.

Step 6

              Left Speaker

Use the flat end of a spudger to pry the I/O board cable connector upward out of its socket on the I/O board.

Use the flat end of a spudger to pry the I/O board cable connector upward out of its socket on the I/O board.

Step 7

Use the tip of a spudger to flip up the retaining flap on the microphone ribbon cable ZIF socket.
Be sure you are prying up on the hinged retaining flap, not the socket itself.
Pull the microphone ribbon cable straight out of its socket.

Use the tip of a spudger to flip up the retaining flap on the microphone ribbon cable ZIF socket.

Be sure you are prying up on the hinged retaining flap, not the socket itself.

Pull the microphone ribbon cable straight out of its socket.

Step 8

Use the tip of a spudger to de-route the left speaker cable from the notch cut into the edge of the I/O board.

Use the tip of a spudger to de-route the left speaker cable from the notch cut into the edge of the I/O board.

Step 9

Use the flat end of a spudger to pry the left speaker connector up and out of its socket on the I/O board.
Pry upward from beneath the wires.

Use the flat end of a spudger to pry the left speaker connector up and out of its socket on the I/O board.

Pry upward from beneath the wires.

Step 10

Use the flat end of a spudger to pry the left speaker off the adhesive securing it to the upper case.
Only pry up on the speaker from the areas of bare aluminum on the upper case. Prying up from the keyboard area may damage the keyboard and the speaker itself.
Remove the left speaker from the upper case.

Use the flat end of a spudger to pry the left speaker off the adhesive securing it to the upper case.

Only pry up on the speaker from the areas of bare aluminum on the upper case. Prying up from the keyboard area may damage the keyboard and the speaker itself.

Remove the left speaker from the upper case.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 4 other contributors

                    Andrew Bookholt

575,478 Reputation

                                      618 Guides authored                  



                       Badges:
                       47







                                                        +44 more badges

Introduction#

What you need#

Introduction

What you need