Macbook Air 11 Late 2010 Fan Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 - 30 minutes

Sections

Lower Case
2 steps
Battery
1 step
Solid-State Drive
2 steps
I/O Board Cable
2 steps
Fan
3 steps

Flags

BackMacBook Air 11" Late 2010
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Lower Case

Before proceeding, close your computer and lay it on a soft surface top-side down.
Remove the following ten screws:
Two 8 mm 5-point Pentalobe screws
Eight 2.5 mm 5-point Pentalobe screws
The special screwdriver needed to remove the eight 5-point Pentalobe screws can be found here.

Before proceeding, close your computer and lay it on a soft surface top-side down.

Remove the following ten screws:

Two 8 mm 5-point Pentalobe screws

Eight 2.5 mm 5-point Pentalobe screws

The special screwdriver needed to remove the eight 5-point Pentalobe screws can be found here.

1024

Step 2

Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.
Remove the lower case and set it aside.

Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.

Remove the lower case and set it aside.

Step 3

              Battery

In this step you will disconnect the battery to help avoid shorting out any components during service.
Use the flat end of a spudger to pry both short sides of the battery connector upward to disconnect it from its socket on the logic board.
Bend the battery cable slightly away from the logic board so the connector will not accidentally contact its socket.

In this step you will disconnect the battery to help avoid shorting out any components during service.

Use the flat end of a spudger to pry both short sides of the battery connector upward to disconnect it from its socket on the logic board.

Bend the battery cable slightly away from the logic board so the connector will not accidentally contact its socket.

Step 4

              Solid-State Drive

Remove the single 2.9 mm T5 Torx screw securing the SSD to the logic board.

Remove the single 2.9 mm T5 Torx screw securing the SSD to the logic board.

Step 5

Use a spudger to help lift the free end of the SSD just enough to grab it with your other hand.
Do not lift the end of the SSD excessively.
Pull the drive straight out of its socket and remove it from the logic board.
When reinstalling the SSD, be sure it is properly seated before reinstalling its retaining screw.

Use a spudger to help lift the free end of the SSD just enough to grab it with your other hand.

Do not lift the end of the SSD excessively.

Pull the drive straight out of its socket and remove it from the logic board.

When reinstalling the SSD, be sure it is properly seated before reinstalling its retaining screw.

Step 6

              I/O Board Cable

Use the flat end of a spudger to pry the I/O board cable connector upward out of its socket on the I/O board.

Use the flat end of a spudger to pry the I/O board cable connector upward out of its socket on the I/O board.

Step 7

The following connector has an especially deep socket. Use care when disconnecting it.
While gently pulling the I/O board cable upward near its connection to the logic board, use the tip of a spudger to pry upward on alternating sides of the connector to help “walk” it out of its socket.
Remove the I/O board cable.

The following connector has an especially deep socket. Use care when disconnecting it.

While gently pulling the I/O board cable upward near its connection to the logic board, use the tip of a spudger to pry upward on alternating sides of the connector to help “walk” it out of its socket.

Remove the I/O board cable.

Step 8

Fan

Use the tip of a spudger to carefully flip up the retaining flap on the fan cable ZIF socket.
Be sure you are prying up on the hinged retaining flap, not the socket itself.

Use the tip of a spudger to carefully flip up the retaining flap on the fan cable ZIF socket.

Be sure you are prying up on the hinged retaining flap, not the socket itself.

Step 9

Remove the following three screws securing the fan to the upper case:
Two 5.2 mm T5 Torx screws
One 3.6 mm T5 Torx screw

Remove the following three screws securing the fan to the upper case:

Two 5.2 mm T5 Torx screws

One 3.6 mm T5 Torx screw

Step 10

Lift the fan out of the upper case and carefully pull the fan ribbon cable out of its socket as you remove it from the Air.

Lift the fan out of the upper case and carefully pull the fan ribbon cable out of its socket as you remove it from the Air.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      9 other people completed this guide.

Author

                                      with 5 other contributors

                    Andrew Bookholt

575,478 Reputation

                                      618 Guides authored                  



                       Badges:
                       47







                                                        +44 more badges

gigi marks - Nov 29, 2018

thanks a million—clear and accessible.And we did it!

Introduction#

What you need#

Introduction

What you need