Featured
Featured Guide
Difficulty
Moderate
Steps
9
Time Required
Suggest a time??
Sections
4
- Lower Case
- 2 steps
- Battery Connector
- 1 step
- Battery
- 2 steps
- Trackpad
- 4 steps
Flags
1
Featured Guide
This guide has been found to be exceptionally cool by the iFixit staff.
BackMacBook Air 11" Early 2015
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Lower Case
- Shut down and close your computer. Lay it on a soft surface top-side down.
- Remove the following ten screws:
- Two 8 mm 5-point Pentalobe screws
- Eight 2.5 mm 5-point Pentalobe screws
- The special screwdriver needed to remove the 5-point Pentalobe screws can be found here.
Shut down and close your computer. Lay it on a soft surface top-side down.
Remove the following ten screws:
Two 8 mm 5-point Pentalobe screws
Eight 2.5 mm 5-point Pentalobe screws
The special screwdriver needed to remove the 5-point Pentalobe screws can be found here.
1024
Step 2
- Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.
Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.
Step 3
Battery Connector
- In this step you will disconnect the battery to help avoid shorting out any components during service.
- Use the flat end of a spudger to pry both short sides of the battery connector upward to disconnect it from its socket on the logic board.
- Bend the battery cable slightly away from the logic board so the connector will not accidentally bend back and make contact with its socket.
In this step you will disconnect the battery to help avoid shorting out any components during service.
Use the flat end of a spudger to pry both short sides of the battery connector upward to disconnect it from its socket on the logic board.
Bend the battery cable slightly away from the logic board so the connector will not accidentally bend back and make contact with its socket.
Step 4
Battery
- Remove the following five screws securing the battery to the upper case:
- Two 5.2 mm T5 Torx screws
- One 6 mm T5 Torx screw
- Two 2.6 mm T5 Torx screws
Remove the following five screws securing the battery to the upper case:
Two 5.2 mm T5 Torx screws
One 6 mm T5 Torx screw
Two 2.6 mm T5 Torx screws
Step 5
- When handling the battery, avoid squeezing or touching the six exposed lithium polymer cells.
- Lift the battery from its edge nearest the logic board and remove it from the upper case.
- If you’re installing a new battery, you should calibrate it after installation:
- Charge it to 100%, and then keep charging it for at least 2 more hours. Next, unplug and use it normally to drain the battery. When you see the low battery warning, save your work, and keep your laptop on until it goes to sleep due to low battery. Wait at least 5 hours, then charge your laptop uninterrupted to 100%.
- If you notice any unusual behavior or problems after installing your new battery, you may need to reset your MacBook’s SMC.
When handling the battery, avoid squeezing or touching the six exposed lithium polymer cells.
Lift the battery from its edge nearest the logic board and remove it from the upper case.
If you’re installing a new battery, you should calibrate it after installation:
Charge it to 100%, and then keep charging it for at least 2 more hours. Next, unplug and use it normally to drain the battery. When you see the low battery warning, save your work, and keep your laptop on until it goes to sleep due to low battery. Wait at least 5 hours, then charge your laptop uninterrupted to 100%.
If you notice any unusual behavior or problems after installing your new battery, you may need to reset your MacBook’s SMC.
Step 6
Trackpad
- Use the point of a spudger to lift the ZIF connector retaining flap on the trackpad data cable.
- Gently slide the ribbon cable out of the ZIF connector.
- Adjust, but do not remove the T5 Trackpad Sensitivity Screw to change the trackpad’s depth sensitivity.
Use the point of a spudger to lift the ZIF connector retaining flap on the trackpad data cable.
Gently slide the ribbon cable out of the ZIF connector.
Adjust, but do not remove the T5 Trackpad Sensitivity Screw to change the trackpad’s depth sensitivity.
Step 7
- With one hand, push the keyboard ribbon cable in slightly to access the ZIF connector beneath it.
- Use a spudger to flip up the retaining flap.
- Gently slide the cable out of the connector.
With one hand, push the keyboard ribbon cable in slightly to access the ZIF connector beneath it.
Use a spudger to flip up the retaining flap.
Gently slide the cable out of the connector.
Step 8
- Remove the six 1.5 mm Phillips #00 screws holding the trackpad in place.
- These screws are installed tightly and strip easily. Be careful as you remove them.
Remove the six 1.5 mm Phillips #00 screws holding the trackpad in place.
These screws are installed tightly and strip easily. Be careful as you remove them.
Step 9
- Open the device about 10 degrees.
- While holding the bottom of the trackpad, press up on the side of the trackpad closest to the logic board to free it from the upper case.
- Remove the trackpad from the device.
Open the device about 10 degrees.
While holding the bottom of the trackpad, press up on the side of the trackpad closest to the logic board to free it from the upper case.
Remove the trackpad from the device.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
9 other people completed this guide.
Author
with 4 other contributors
Sam Goldheart
Member since: 10/18/2012
455,549 Reputation
548 Guides authored
Badges:
48
+45 more badges
Team
iFixit
Member of iFixit
Community
141 Members
15,767 Guides authored
iamsyed1987 - Nov 28, 2019
Reply
Or is there another problem? I noticed there are two black rubber pads (made of a thin foam) that are between the base of the trackpad and the body of the macbook frame, and that in my computer they are worn/frayed. Could this be the problem?
If anyone has any knowledge about this, or advice about how to go about with this repair and trying different things, I would appreciate your help.
Brittany Santos - May 17, 2021
I’d love to know the answers to the above questions before I take mine apart!
ejri bejri - Jul 17, 2022
Reply
this was very easy thanks