Difficulty

Moderate

Steps

33

Time Required

Suggest a time??

Sections

8

  • Outer Case
  • 2 steps
  • Fan Assembly
  • 6 steps
  • Lower Case
  • 2 steps
  • Interconnect Board
  • 6 steps
  • Power Supply Assembly
  • 5 steps
  • Power Supply
  • 5 steps
  • IO Board
  • 4 steps
  • Speaker
  • 3 steps

Flags

0

  • BackMac Pro 2013

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

Before beginning any work on your Mac Pro: Unplug the computer and press and hold the power button for ten seconds to discharge the power supply’s capacitors.

Be very careful not to touch the capacitor leads or any exposed solder joints on the back of the power supply. Only handle the board by the edges.

What you need

Step 1

              Outer Case
  • Slide the lock switch to the right, to the unlocked position.

Slide the lock switch to the right, to the unlocked position.

1024

Step 2

  • Lift the outer case straight up off the Mac Pro.
  • It may help to push down on the center of the fan while lifting the case up.

Lift the outer case straight up off the Mac Pro.

It may help to push down on the center of the fan while lifting the case up.

Step 3

              Fan Assembly
  • Remove five 5.1 mm T10 Torx screws from around the outer perimeter of the fan assembly.

Remove five 5.1 mm T10 Torx screws from around the outer perimeter of the fan assembly.

Step 4

  • The fan assembly is attached to the rest of the computer by two cables on the IO board side.
  • Tilt the assembly up away from the IO board.
  • Do not try to remove the fan assembly yet, as it is still attached by two cables.

The fan assembly is attached to the rest of the computer by two cables on the IO board side.

Tilt the assembly up away from the IO board.

Do not try to remove the fan assembly yet, as it is still attached by two cables.

Step 5

  • While supporting the fan assembly with one hand, loosen the two T8 captive screws in the fan cable bracket.
  • These screws are captive in the Mac Pro. Do not try to remove these screws from your Mac Pro.

While supporting the fan assembly with one hand, loosen the two T8 captive screws in the fan cable bracket.

These screws are captive in the Mac Pro. Do not try to remove these screws from your Mac Pro.

Step 6

  • Use a pair of tweezers to pull the fan cable bracket away from the fan assembly.

Use a pair of tweezers to pull the fan cable bracket away from the fan assembly.

Step 7

  • Use the flat end of a spudger to disconnect the fan assembly ribbon cable from the IO board.

Use the flat end of a spudger to disconnect the fan assembly ribbon cable from the IO board.

Step 8

  • Disconnect the fan assembly antenna cable from the IO board.
  • Remove the fan assembly from the Mac Pro.

Disconnect the fan assembly antenna cable from the IO board.

Remove the fan assembly from the Mac Pro.

Step 9

              Lower Case
  • Flip the Mac Pro upside down, 180 degrees.
  • Remove five 5.1 mm T10 Torx screws from the outer perimeter of the lower case.

Flip the Mac Pro upside down, 180 degrees.

Remove five 5.1 mm T10 Torx screws from the outer perimeter of the lower case.

Step 10

  • Carefully lift the lower case up and remove it from the Mac Pro.

Carefully lift the lower case up and remove it from the Mac Pro.

Step 11

              Interconnect Board
  • Use the flat end of a spudger and a twisting motion to gently separate one side of the graphics card data connection.

Use the flat end of a spudger and a twisting motion to gently separate one side of the graphics card data connection.

Step 12

  • Gently separate the other side as well.
  • Flip the connector up and out of the way of the graphics card.
  • Repeat this procedure on the other graphics card.

Gently separate the other side as well.

Flip the connector up and out of the way of the graphics card.

Repeat this procedure on the other graphics card.

Step 13

  • Remove the two 6.0 mm T8 Torx screws securing the interconnect board to the heat sink.

Remove the two 6.0 mm T8 Torx screws securing the interconnect board to the heat sink.

Step 14

  • Gently walk the interconnect board straight up off the logic board’s slot connection.
  • It is recommended to lift one side and then the other.
  • Do not try to remove the interconnect board from the Mac Pro yet, as it is still connected to the IO board.

Gently walk the interconnect board straight up off the logic board’s slot connection.

It is recommended to lift one side and then the other.

Do not try to remove the interconnect board from the Mac Pro yet, as it is still connected to the IO board.

Step 15

  • Flip the interconnect board up and over, exposing the IO board data cable.
  • Use the same sort of twisting and spreading motion with the flat end of a spudger to separate one side of the IO board data cable.

Flip the interconnect board up and over, exposing the IO board data cable.

Use the same sort of twisting and spreading motion with the flat end of a spudger to separate one side of the IO board data cable.

Step 16

  • Use the flat end of a spudger to separate the other side of the IO board data cable.
  • Bend the cable out of the way and remove the interconnect board from the Mac Pro.

Use the flat end of a spudger to separate the other side of the IO board data cable.

Bend the cable out of the way and remove the interconnect board from the Mac Pro.

Step 17

              Power Supply Assembly
  • Flip the Mac Pro back over and set it gently on a flat surface.
  • We recommend laying the Mac Pro on the corner of the heat sink and the two standoff screw posts that attach to the interconnect board.

Flip the Mac Pro back over and set it gently on a flat surface.

We recommend laying the Mac Pro on the corner of the heat sink and the two standoff screw posts that attach to the interconnect board.

Step 18

  • Remove the two 3.6 mm T5 Torx screws from the sides of the power supply cage (one on each side).

Remove the two 3.6 mm T5 Torx screws from the sides of the power supply cage (one on each side).

Step 19

  • Remove the power supply cage from the top of the power supply.
  • By removing this cage, you are exposing internal components of the power supply. Be very careful not to touch any of the power supply components or circuitry.
  • Be careful not to drop any screws or tools into the power supply, as this may damage the power supply.

Remove the power supply cage from the top of the power supply.

By removing this cage, you are exposing internal components of the power supply. Be very careful not to touch any of the power supply components or circuitry.

Be careful not to drop any screws or tools into the power supply, as this may damage the power supply.

Step 20

  • Remove the four 5.5 mm T8 Torx screws securing the power supply assembly to the Mac Pro.

Remove the four 5.5 mm T8 Torx screws securing the power supply assembly to the Mac Pro.

Step 21

  • Remove the power supply assembly from the Mac Pro.

Remove the power supply assembly from the Mac Pro.

Step 22

              Power Supply
  • Use the flat end of a spudger to disconnect the power supply DC-Out connector from its socket on the IO board.
  • Use the tip of a spudger to disconnect the power supply data cable from its socket on the IO board.
  • For both cables, make sure to pry straight up on the connector, and not the socket.

Use the flat end of a spudger to disconnect the power supply DC-Out connector from its socket on the IO board.

Use the tip of a spudger to disconnect the power supply data cable from its socket on the IO board.

For both cables, make sure to pry straight up on the connector, and not the socket.

Step 23

  • Remove the four 9.0 mm silver T10 Torx screws from the sides of the power supply.
  • The power supply overhangs these screws somewhat, so you’ll need to use a fixed screwdriver at a bit of an angle.

Remove the four 9.0 mm silver T10 Torx screws from the sides of the power supply.

The power supply overhangs these screws somewhat, so you’ll need to use a fixed screwdriver at a bit of an angle.

Step 24

  • Gently shift the power supply to free the AC power inlet cable out of its plastic clip.
  • Be careful not to try to separate the power supply from the IO board assembly just yet, as it is still connected by the AC power inlet cable.

Gently shift the power supply to free the AC power inlet cable out of its plastic clip.

Be careful not to try to separate the power supply from the IO board assembly just yet, as it is still connected by the AC power inlet cable.

Step 25

  • Flip the power supply back to expose the AC power inlet cable.

Flip the power supply back to expose the AC power inlet cable.

Step 26

  • Squeeze the AC power inlet cable connector and pull it straight out of its socket in the power supply.

Squeeze the AC power inlet cable connector and pull it straight out of its socket in the power supply.

Step 27

              IO Board
  • Remove the two 9 mm silver T10 Torx screws securing the IO Board to the IO shield.

Remove the two 9 mm silver T10 Torx screws securing the IO Board to the IO shield.

Step 28

  • Lift the IO board up from the IO shield from the end with the AC plug.
  • Do not attempt to completely separate the IO board from the IO shield, as there are still two cables connecting the two components.

Lift the IO board up from the IO shield from the end with the AC plug.

Do not attempt to completely separate the IO board from the IO shield, as there are still two cables connecting the two components.

Step 29

  • Set the assembly down on a flat surface to access the connectors on the IO board.
  • Use the tip of a spudger to flip the retaining flap on the IO shield ribbon cable ZIF connector.
  • Disconnect the IO shield ribbon cable.

Set the assembly down on a flat surface to access the connectors on the IO board.

Use the tip of a spudger to flip the retaining flap on the IO shield ribbon cable ZIF connector.

Disconnect the IO shield ribbon cable.

Step 30

  • Squeeze and pull the audio jack ribbon cable connector from the IO board.

Squeeze and pull the audio jack ribbon cable connector from the IO board.

Step 31

              Speaker
  • Use the tip of a spudger to disconnect the speaker cable from its socket on the IO board.
  • Be careful to pry up on the connector and not the socket.

Use the tip of a spudger to disconnect the speaker cable from its socket on the IO board.

Be careful to pry up on the connector and not the socket.

Step 32

  • Remove the two 3.2 mm T4 Torx screws securing the speaker to the IO board.

Remove the two 3.2 mm T4 Torx screws securing the speaker to the IO board.

Step 33

  • Remove the speaker from the IO board.

Remove the speaker from the IO board.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 1 other contributor 


                    Andrew Optimus Goldheart

Member since: 10/17/2009

491,689 Reputation

                                      411 Guides authored                  



                       Badges:
                       44







                                                        +41 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,767 Guides authored

Jimmy Leow - Dec 24, 2021

Reply

Do you sell this speaker parts ?