Mac Pro Late 2013 Graphics Card Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          1 hour

Sections

Outer Case
2 steps
Fan Assembly
6 steps
Lower Case
2 steps
Graphics Card
7 steps

Flags

BackMac Pro 2013
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

When you’re replacing your card, be sure to reapply a layer of thermal compound.

Before beginning any work on your Mac Pro: Unplug the computer and press and hold the power button for ten seconds to discharge the power supply’s capacitors.

Be very careful not to touch the capacitor leads or any exposed solder joints on the back of the power supply. Only handle the board by the edges.

What you need

Step 1

              Outer Case

Slide the lock switch to the right, to the unlocked position.

Slide the lock switch to the right, to the unlocked position.

1024

Step 2

Lift the outer case straight up off the Mac Pro.
It may help to push down on the center of the fan while lifting the case up.

Lift the outer case straight up off the Mac Pro.

It may help to push down on the center of the fan while lifting the case up.

Step 3

              Fan Assembly

Remove five 5.1 mm T10 Torx screws from around the outer perimeter of the fan assembly.

Remove five 5.1 mm T10 Torx screws from around the outer perimeter of the fan assembly.

Step 4

The fan assembly is attached to the rest of the computer by two cables on the IO board side.
Tilt the assembly up away from the IO board.
Do not try to remove the fan assembly yet, as it is still attached by two cables.

The fan assembly is attached to the rest of the computer by two cables on the IO board side.

Tilt the assembly up away from the IO board.

Do not try to remove the fan assembly yet, as it is still attached by two cables.

Step 5

While supporting the fan assembly with one hand, loosen the two T8 captive screws in the fan cable bracket.
These screws are captive in the Mac Pro. Do not try to remove these screws from your Mac Pro.

While supporting the fan assembly with one hand, loosen the two T8 captive screws in the fan cable bracket.

These screws are captive in the Mac Pro. Do not try to remove these screws from your Mac Pro.

Step 6

Use a pair of tweezers to pull the fan cable bracket away from the fan assembly.

Use a pair of tweezers to pull the fan cable bracket away from the fan assembly.

Step 7

Use the flat end of a spudger to disconnect the fan assembly ribbon cable from the IO board.

Use the flat end of a spudger to disconnect the fan assembly ribbon cable from the IO board.

Step 8

Disconnect the fan assembly antenna cable from the IO board.
Remove the fan assembly from the Mac Pro.

Disconnect the fan assembly antenna cable from the IO board.

Remove the fan assembly from the Mac Pro.

Step 9

              Lower Case

Flip the Mac Pro upside down, 180 degrees.
Remove five 5.1 mm T10 Torx screws from the outer perimeter of the lower case.

Flip the Mac Pro upside down, 180 degrees.

Remove five 5.1 mm T10 Torx screws from the outer perimeter of the lower case.

Step 10

Carefully lift the lower case up and remove it from the Mac Pro.

Carefully lift the lower case up and remove it from the Mac Pro.

Step 11

              Graphics Card

Use the flat end of a spudger and a twisting motion to gently separate one side of the graphics card data connection.

Use the flat end of a spudger and a twisting motion to gently separate one side of the graphics card data connection.

Step 12

Gently separate the other side as well.
Flip the connector up and out of the way of the graphics card.

Gently separate the other side as well.

Flip the connector up and out of the way of the graphics card.

Step 13

Remove the two 6.6 mm T8 Torx Security screws securing the GPU to the Mac Pro.
These screws fit into power cables behind the GPU. Be careful not to over-tighten and twist the cables.

Remove the two 6.6 mm T8 Torx Security screws securing the GPU to the Mac Pro.

These screws fit into power cables behind the GPU. Be careful not to over-tighten and twist the cables.

Step 14

Remove the four 8.4 mm T10 screws from the GPU heat sink bracket.

Remove the four 8.4 mm T10 screws from the GPU heat sink bracket.

Step 15

Remove the GPU heat sink bracket.

Remove the GPU heat sink bracket.

Step 16

The graphics card is now held onto the central heat sink by thermal compound.
You may need to pry very gently with a spudger to separate the card from the heat sink.
Remove the graphics card from the heat sink.

The graphics card is now held onto the central heat sink by thermal compound.

You may need to pry very gently with a spudger to separate the card from the heat sink.

Remove the graphics card from the heat sink.

Step 17

During reassembly, be sure to clean off and replace the thermal compound. Use our Applying Thermal Paste guide if you require assistance.
Repeat this procedure if you wish to remove the secondary graphics card.

During reassembly, be sure to clean off and replace the thermal compound. Use our Applying Thermal Paste guide if you require assistance.

Repeat this procedure if you wish to remove the secondary graphics card.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      36 other people completed this guide.

Author

                                      with 3 other contributors

                    Andrew Optimus Goldheart

Member since: 10/17/2009

491,689 Reputation

                                      411 Guides authored                  



                       Badges:
                       44







                                                        +41 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,767 Guides authored

Ben - Jun 25, 2014

hey! is it possible to upgrade the GPU or is this just for replacing exactly the same part?

Fernando Bernardino - Sep 25, 2014

I am guessing you can upgrade them with OEM parts, but where would we find them?

Technology Research - Aug 16, 2022

Yes. I recently swapped out D300 pairs for D700 pairs without a blip. I did an NVRAM reset afterwards just to be safe.

Chris M Balz - Jul 14, 2015

I have the D300s, and would like to upgrade to the D500s or D700s. Where might I find the replacement graphics cards? Also, any recommendations on service providers who would do this procedure?

jerimiahy - Aug 24, 2015

I’d love to know this as well. The only reason I picked up the ,ad pro was the potential for upgrades. As it turns out D300s are crap. I can’t even run boot camp properly.

Introduction#

What you need#

Team#

Introduction

What you need

Team