Difficulty
Moderate
Steps
10
Time Required
1 - 2 hours
Sections
4
- Outer Mesh
- 3 steps
- Battery
- 3 steps
- Speaker
- 3 steps
- Motherboard
- 1 step
Flags
0
BackLogitech UE Megaboom
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Outer Mesh
- Locate the ends of the speaker.
- Put a plastic opening tool in-between the rubber end and the mesh.
- Apply a upward force in order to pry open the end.
- Apply this procedure to the other side as well.
- Will take force.
- Using metal tools may permanently mar your device.
Locate the ends of the speaker.
Put a plastic opening tool in-between the rubber end and the mesh.
Apply a upward force in order to pry open the end.
Apply this procedure to the other side as well.
Will take force.
Using metal tools may permanently mar your device.
1024
Step 2
- Take the Jimmy and pry up the rubber strip that has the volume buttons on it.
- You will hear clicks as it pries up, don’t worry.
- Remove all the rubber you pried off.
Take the Jimmy and pry up the rubber strip that has the volume buttons on it.
You will hear clicks as it pries up, don’t worry.
Remove all the rubber you pried off.
Step 3
- Use tweezers to lift end of plastic retainer on edge of mesh out of its channel.
- Work the plastic retainer out of the channel all the way around the speaker.
- Be gentle, it is easy to damage the fabric.
- Repeat for other side.
Use tweezers to lift end of plastic retainer on edge of mesh out of its channel.
Work the plastic retainer out of the channel all the way around the speaker.
Be gentle, it is easy to damage the fabric.
Repeat for other side.
Step 4
Battery
- Pull on white strip to remove battery.
Pull on white strip to remove battery.
Step 5
- Remove inner plastic gasket on circuit board.
- Remove 2nd plastic gasket around outer circuit board edge, under rubber gasket.
Remove inner plastic gasket on circuit board.
Remove 2nd plastic gasket around outer circuit board edge, under rubber gasket.
Step 6
- Gently pry circuit board up out of recess.
Gently pry circuit board up out of recess.
Step 7
Speaker
- Insert a opening tool between the grating and the body of the speaker
- Pry up allowing the tabs to pop out of place.
- There will be an audible sound when the tabs have begun to pop out of place.
- Apply the same procedure to the grating covering the second speaker.
Insert a opening tool between the grating and the body of the speaker
Pry up allowing the tabs to pop out of place.
There will be an audible sound when the tabs have begun to pop out of place.
Apply the same procedure to the grating covering the second speaker.
Step 8
- Use a opening tool to push the thin metal rod located on the side of the speaker out.
- Using needle nose pliers grasp the rod and pull the rod out of the speaker until fully removed.
- Remove the remaining three rods.
- One is located on the same side and two are located on the other speaker.
Use a opening tool to push the thin metal rod located on the side of the speaker out.
Using needle nose pliers grasp the rod and pull the rod out of the speaker until fully removed.
Remove the remaining three rods.
One is located on the same side and two are located on the other speaker.
Step 9
- Insert a opening tool between the speaker and the base
- Pry up allowing the speaker tabs to pop out of place
- Find and disconnect the wire from the motherboard by pulling in an upward motion.
- Apply the same procedure to the second speaker.
Insert a opening tool between the speaker and the base
Pry up allowing the speaker tabs to pop out of place
Find and disconnect the wire from the motherboard by pulling in an upward motion.
Apply the same procedure to the second speaker.
Step 10
Motherboard
- Grasp the mother board by the wider edge and pull towards yourself.
- This should not require much force.
Grasp the mother board by the wider edge and pull towards yourself.
This should not require much force.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 3 other contributors
Oscar Ambriz
Member since: 09/27/2017
934 Reputation
6 Guides authored
Badges:
12
+9 more badges
Team
Cal Poly, Team S9-G2, Banghart Fall 2017
Member of Cal Poly, Team S9-G2, Banghart Fall 2017
CPSU-BANGHART-F17S9G2
4 Members
11 Guides authored