Difficulty
Difficult
Steps
25
Time Required
50 minutes
Sections
2
- Speaker Grille
- 13 steps
- Speaker
- 12 steps
Flags
1
Better Introduction
Improve this guide by completing or revising its introduction.
BackLogitech UE Boombox
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Speaker Grille
- Use a metal spudger to pry open the power button cover.
- Once the power button cover is slightly opened, use your fingers to remove the power button cover.
Use a metal spudger to pry open the power button cover.
Once the power button cover is slightly opened, use your fingers to remove the power button cover.
1024
Step 2
- Press firmly on the end of the latch and pull the two-wire connector away from the base to separate.
Press firmly on the end of the latch and pull the two-wire connector away from the base to separate.
Step 3
- Firmly press on the end of the latch and pull the four-wire connector away from the base to separate.
Firmly press on the end of the latch and pull the four-wire connector away from the base to separate.
Step 4
- Lightly, pry up on each side of the black band connector lock using your fingertips.
- Once unlocked, pull straight up on the connector to remove.
Lightly, pry up on each side of the black band connector lock using your fingertips.
Once unlocked, pull straight up on the connector to remove.
Step 5
- Remove the five black 14mm Phillips #2 screws from the black plastic side panel.
- Remove the one silver 16mm Phillips #2 screws from the black plastic side panel.
- Remove the black plastic screw panel from the boombox.
Remove the five black 14mm Phillips #2 screws from the black plastic side panel.
Remove the one silver 16mm Phillips #2 screws from the black plastic side panel.
Remove the black plastic screw panel from the boombox.
Step 6
- On the opposite side of the device, pry open the volume rocker with a metal spudger.
- Remove the panel with your fingers once the volume rocker is slightly opened.
On the opposite side of the device, pry open the volume rocker with a metal spudger.
Remove the panel with your fingers once the volume rocker is slightly opened.
Step 7
- Remove the five black 14mm Phillips #2 screws from the black plastic side panel.
- Remove the one silver16 mm Phillips #2 screw from the black plastic side panel.
- Once all screws are removed, take the screw panel out of the device to gain access to the back of the panel.
Remove the one silver16 mm Phillips #2 screw from the black plastic side panel.
Once all screws are removed, take the screw panel out of the device to gain access to the back of the panel.
Step 8
- Firmly press on the end of the latch and pull the two-wire connector away from the base.
Firmly press on the end of the latch and pull the two-wire connector away from the base.
Step 9
- Pull up on the aluminum boombox handle to remove.
Pull up on the aluminum boombox handle to remove.
Step 10
- Use a metal spudger to pry the rubber base apart from the aluminum grille.
Use a metal spudger to pry the rubber base apart from the aluminum grille.
Step 11
- Pull the rubber base away from the boombox.
Pull the rubber base away from the boombox.
Step 12
- Remove the four black 7.5mm Phillips #2 screws on each side of the device.
- There should be a total of eight screws removed in this step.
Remove the four black 7.5mm Phillips #2 screws on each side of the device.
There should be a total of eight screws removed in this step.
Step 13
- Pull vertically on the speaker grille to remove it from the boombox.
Pull vertically on the speaker grille to remove it from the boombox.
Step 14
Speaker
- Remove the fifteen 13.0 mm screws with a #0 Phillips from the side of the device containing two speakers.
- Separate the two halves by gently pulling them apart.
- The screws at this step are embedded deep within the device so make sure your screw driver is long.
Remove the fifteen 13.0 mm screws with a #0 Phillips from the side of the device containing two speakers.
Separate the two halves by gently pulling them apart.
The screws at this step are embedded deep within the device so make sure your screw driver is long.
Step 15
- Locate the speaker adjacent to the motherboard.
Locate the speaker adjacent to the motherboard.
Step 16
- Desolder all four wires connecting the speaker.
- One red and one black wire are located on each side of speaker.
- Check out the How to Solder and Desolder Connections guide for soldering help.
Desolder all four wires connecting the speaker.
One red and one black wire are located on each side of speaker.
Check out the How to Solder and Desolder Connections guide for soldering help.
Step 17
- Remove the four 7.0 mm screws with a Phillips #2.
Remove the four 7.0 mm screws with a Phillips #2.
Step 18
- Lift the speaker out of the device using your fingers.
Lift the speaker out of the device using your fingers.
Step 19
- Pull up on the lock to detach the band connector from the motherboard.
Pull up on the lock to detach the band connector from the motherboard.
Step 20
- Remove five 7.0 mm screws on the motherboard with a Phillips #2.
Remove five 7.0 mm screws on the motherboard with a Phillips #2.
Step 21
- Lift the motherboard with your fingers.
- Flip over to reveal the underside.
- Motherboard will still be attached to the device.
Lift the motherboard with your fingers.
Flip over to reveal the underside.
Motherboard will still be attached to the device.
Step 22
- Pull up on the lock of the band connector to detach it from the motherboard.
Pull up on the lock of the band connector to detach it from the motherboard.
Step 23
- Desolder all four wires connecting the speaker.
- One red and one black wire are located on each side of speaker.
Step 24
- Remove four 7.0 mm screws with a Phillips #2.
Remove four 7.0 mm screws with a Phillips #2.
Step 25
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
3 other people completed this guide.
Author
with 3 other contributors
Breean Mokede
Member since: 09/15/2016
282 Reputation
2 Guides authored
Badges:
7
+4 more badges
Team
CSU Fullerton, Team 1-1, Bruce Fall 2016
Member of CSU Fullerton, Team 1-1, Bruce Fall 2016
CSUF-BRUCE-F16S1G1
4 Members
5 Guides authored
Ted Glasgow - Dec 29, 2019
Reply
Could you recommend anywhere to find the correct replacement tweeters & drivers?