Difficulty
Moderate
Steps
18
Time Required
35 minutes
Sections
2
- Speaker Grille
- 13 steps
- Bluetooth Adapter
- 5 steps
Flags
1
Featured Student Guide
This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.
BackLogitech UE Boombox
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Speaker Grille
- Use a metal spudger to pry open the power button cover.
- Once the power button cover is slightly opened, use your fingers to remove the power button cover.
Use a metal spudger to pry open the power button cover.
Once the power button cover is slightly opened, use your fingers to remove the power button cover.
1024
Step 2
- Press firmly on the end of the latch and pull the two-wire connector away from the base to separate.
Press firmly on the end of the latch and pull the two-wire connector away from the base to separate.
Step 3
- Firmly press on the end of the latch and pull the four-wire connector away from the base to separate.
Firmly press on the end of the latch and pull the four-wire connector away from the base to separate.
Step 4
- Lightly, pry up on each side of the black band connector lock using your fingertips.
- Once unlocked, pull straight up on the connector to remove.
Lightly, pry up on each side of the black band connector lock using your fingertips.
Once unlocked, pull straight up on the connector to remove.
Step 5
- Remove the five black 14mm Phillips #2 screws from the black plastic side panel.
- Remove the one silver 16mm Phillips #2 screws from the black plastic side panel.
- Remove the black plastic screw panel from the boombox.
Remove the five black 14mm Phillips #2 screws from the black plastic side panel.
Remove the one silver 16mm Phillips #2 screws from the black plastic side panel.
Remove the black plastic screw panel from the boombox.
Step 6
- On the opposite side of the device, pry open the volume rocker with a metal spudger.
- Remove the panel with your fingers once the volume rocker is slightly opened.
On the opposite side of the device, pry open the volume rocker with a metal spudger.
Remove the panel with your fingers once the volume rocker is slightly opened.
Step 7
- Remove the five black 14mm Phillips #2 screws from the black plastic side panel.
- Remove the one silver16 mm Phillips #2 screw from the black plastic side panel.
- Once all screws are removed, take the screw panel out of the device to gain access to the back of the panel.
Remove the one silver16 mm Phillips #2 screw from the black plastic side panel.
Once all screws are removed, take the screw panel out of the device to gain access to the back of the panel.
Step 8
- Firmly press on the end of the latch and pull the two-wire connector away from the base.
Firmly press on the end of the latch and pull the two-wire connector away from the base.
Step 9
- Pull up on the aluminum boombox handle to remove.
Pull up on the aluminum boombox handle to remove.
Step 10
- Use a metal spudger to pry the rubber base apart from the aluminum grille.
Use a metal spudger to pry the rubber base apart from the aluminum grille.
Step 11
- Pull the rubber base away from the boombox.
Pull the rubber base away from the boombox.
Step 12
- Remove the four black 7.5mm Phillips #2 screws on each side of the device.
- There should be a total of eight screws removed in this step.
Remove the four black 7.5mm Phillips #2 screws on each side of the device.
There should be a total of eight screws removed in this step.
Step 13
- Pull vertically on the speaker grille to remove it from the boombox.
Pull vertically on the speaker grille to remove it from the boombox.
Step 14
Bluetooth Adapter
- Remove the fifteen 13.0mm Phillips #2 screws from the side of the device containing two speakers.
- Separate the two halves by gently pulling them apart.
- The screws at this step are embedded deep within the device so make sure your screwdriver is long.
Remove the fifteen 13.0mm Phillips #2 screws from the side of the device containing two speakers.
Separate the two halves by gently pulling them apart.
The screws at this step are embedded deep within the device so make sure your screwdriver is long.
Step 15
- Pull up on the lock connecting the band connector to the motherboard with your finger tips.
- Detach the band connector gently from the motherboard.
Pull up on the lock connecting the band connector to the motherboard with your finger tips.
Detach the band connector gently from the motherboard.
Step 16
- Remove the five black 7.0mm Phillips #2 screws.
Remove the five black 7.0mm Phillips #2 screws.
Step 17
- Move the motherboard away from bluetooth adapter gently.
- Remove two 7.0mm Phillips #2 screws.
- Motherboard will still be attached to device.
Move the motherboard away from bluetooth adapter gently.
Remove two 7.0mm Phillips #2 screws.
Motherboard will still be attached to device.
Step 18
- Remove the bluetooth adapter from the boombox.
Remove the bluetooth adapter from the boombox.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 4 other contributors
teresa ahmadyar
Member since: 10/06/2016
101 Reputation
1 Guide authored
Badges:
3
Team
CSU Fullerton, Team 1-1, Bruce Fall 2016
Member of CSU Fullerton, Team 1-1, Bruce Fall 2016
CSUF-BRUCE-F16S1G1
4 Members
5 Guides authored