Difficulty
Moderate
Steps
10
Time Required
10 - 15 minutes
Sections
2
- Battery
- 7 steps
- Motherboard
- 3 steps
Flags
0
BackLogitech Harmony Ultimate
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Remove the single 6 mm Phillips #0 screw located beneath the sticker near the USB charging port.
Remove the single 6 mm Phillips #0 screw located beneath the sticker near the USB charging port.
1024
Step 2
- Use a plastic opening tool to release tabs that hold the front panel and back panel together. There are three tabs on each side of the device that need to separate for the device to open.
- The use of a plastic opening tool is recommended to avoid damaging the remote. Use stronger tools as a last resort.
Use a plastic opening tool to release tabs that hold the front panel and back panel together. There are three tabs on each side of the device that need to separate for the device to open.
The use of a plastic opening tool is recommended to avoid damaging the remote. Use stronger tools as a last resort.
Step 3
- Disconnect the wires running from the back cover to the motherboard.
Disconnect the wires running from the back cover to the motherboard.
Step 4
- Remove the four 6mm Phillips #0 screws from the battery case.
Remove the four 6mm Phillips #0 screws from the battery case.
Step 5
- The battery is still connected to the device via wiring. To free the battery completely, remove the dark plastic piece from the slot with the plastic opening tool. Slowly rotate the dark plastic piece and the battery clockwise until then can be removed from underneath the small circuit board with the USB port.
- Removing the dark plastic piece from the motherboard takes some patience, as the remote is designed so that the battery will not dislocate under extreme conditions. The small circuit board with the USB port remains connected to the motherboard by six 10 mm pins.
The battery is still connected to the device via wiring. To free the battery completely, remove the dark plastic piece from the slot with the plastic opening tool. Slowly rotate the dark plastic piece and the battery clockwise until then can be removed from underneath the small circuit board with the USB port.
Removing the dark plastic piece from the motherboard takes some patience, as the remote is designed so that the battery will not dislocate under extreme conditions. The small circuit board with the USB port remains connected to the motherboard by six 10 mm pins.
Step 6
- Lift the battery and its case out of the remote.
- The battery should still be connected to the case with adhesive.
Lift the battery and its case out of the remote.
The battery should still be connected to the case with adhesive.
Step 7
- Use the plastic opening tool to separate the battery from the case.
Use the plastic opening tool to separate the battery from the case.
Step 8
Motherboard
- Remove the four 6mm Phillips #0 screws from the motherboard.
Remove the four 6mm Phillips #0 screws from the motherboard.
Step 9
- There is a flap that connects to the motherboard from the plastic casing. Use fingernails to safely release the flap by flipping the small black buckle upwards.
- The flap and buckle are underneath the clear yellow piece of tape.
- Be very careful as damaging this flap could permanently damage your controller.
There is a flap that connects to the motherboard from the plastic casing. Use fingernails to safely release the flap by flipping the small black buckle upwards.
The flap and buckle are underneath the clear yellow piece of tape.
Be very careful as damaging this flap could permanently damage your controller.
Step 10
- The motherboard is now safe to remove by sliding and lifting it backwards out of place.
The motherboard is now safe to remove by sliding and lifting it backwards out of place.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 6 other contributors
Aaron Diaz
Member since: 08/31/2015
595 Reputation
3 Guides authored
Badges:
12
+9 more badges
Team
USF Tampa, Team 8-1, Eyestone Fall 2015
Member of USF Tampa, Team 8-1, Eyestone Fall 2015
USFT-EYESTONE-F15S8G1
5 Members
5 Guides authored
