Difficulty

Moderate

Steps

11

Time Required

                          10 - 20 minutes

Sections

3

  • Battery
  • 7 steps
  • Motherboard
  • 3 steps
  • Buttons
  • 1 step

Flags

0

  • BackLogitech Harmony Ultimate

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Remove the single 6 mm Phillips #0 screw located beneath the sticker near the USB charging port.

Remove the single 6 mm Phillips #0 screw located beneath the sticker near the USB charging port.

1024

Step 2

  • Use a plastic opening tool to release tabs that hold the front panel and back panel together. There are three tabs on each side of the device that need to separate for the device to open.
  • The use of a plastic opening tool is recommended to avoid damaging the remote. Use stronger tools as a last resort.

Use a plastic opening tool to release tabs that hold the front panel and back panel together. There are three tabs on each side of the device that need to separate for the device to open.

The use of a plastic opening tool is recommended to avoid damaging the remote. Use stronger tools as a last resort.

Step 3

  • Disconnect the wires running from the back cover to the motherboard.

Disconnect the wires running from the back cover to the motherboard.

Step 4

  • Remove the four 6mm Phillips #0 screws from the battery case.

Remove the four 6mm Phillips #0 screws from the battery case.

Step 5

  • The battery is still connected to the device via wiring. To free the battery completely, remove the dark plastic piece from the slot with the plastic opening tool. Slowly rotate the dark plastic piece and the battery clockwise until then can be removed from underneath the small circuit board with the USB port.
  • Removing the dark plastic piece from the motherboard takes some patience, as the remote is designed so that the battery will not dislocate under extreme conditions. The small circuit board with the USB port remains connected to the motherboard by six 10 mm pins.

The battery is still connected to the device via wiring. To free the battery completely, remove the dark plastic piece from the slot with the plastic opening tool. Slowly rotate the dark plastic piece and the battery clockwise until then can be removed from underneath the small circuit board with the USB port.

Removing the dark plastic piece from the motherboard takes some patience, as the remote is designed so that the battery will not dislocate under extreme conditions. The small circuit board with the USB port remains connected to the motherboard by six 10 mm pins.

Step 6

  • Lift the battery and its case out of the remote.
  • The battery should still be connected to the case with adhesive.

Lift the battery and its case out of the remote.

The battery should still be connected to the case with adhesive.

Step 7

  • Use the plastic opening tool to separate the battery from the case.

Use the plastic opening tool to separate the battery from the case.

Step 8

              Motherboard
  • Remove the four 6mm Phillips #0 screws from the motherboard.

Remove the four 6mm Phillips #0 screws from the motherboard.

Step 9

  • There is a flap that connects to the motherboard from the plastic casing. Use fingernails to safely release the flap by flipping the small black buckle upwards.
  • The flap and buckle are underneath the clear yellow piece of tape.
  • Be very careful as damaging this flap could permanently damage your controller.

There is a flap that connects to the motherboard from the plastic casing. Use fingernails to safely release the flap by flipping the small black buckle upwards.

The flap and buckle are underneath the clear yellow piece of tape.

Be very careful as damaging this flap could permanently damage your controller.

Step 10

  • The motherboard is now safe to remove by sliding and lifting it backwards out of place.

The motherboard is now safe to remove by sliding and lifting it backwards out of place.

Step 11

              Buttons
  • After successfully removing the motherboard, you can easily peel off the buttons from the controller frame.

After successfully removing the motherboard, you can easily peel off the buttons from the controller frame.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 4 other contributors 


                    Aaron Diaz

Member since: 08/31/2015

595 Reputation

                                      3 Guides authored                  



                       Badges:
                       12







                                                        +9 more badges

Team

                       USF Tampa, Team 8-1, Eyestone Fall 2015                        

                                                  Member of USF Tampa, Team 8-1, Eyestone Fall 2015 



                    USFT-EYESTONE-F15S8G1                     


                                            5 Members                     


                                            5 Guides authored

Steve Feldner - Mar 23, 2017

Reply

This is a great demo and it give me much more confidence to tackle the repair. I have some questions. Does the battery need to be removed as I see from your pictures, the motherboard screws are not covered by the battery - or are they? Also, where do you purchase your repair parts? Thank you!

larrybud2004 - Apr 28, 2018

Reply

Where do you find the parts? The Logitech website doesn’t have parts for the Ultimate