Difficulty
Easy
Steps
11
Time Required
20 minutes
Sections
2
- Back Panel
- 9 steps
- Ribbon Flex Cable
- 2 steps
Flags
0
BackLogitech Harmony Smart Keyboard
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
The ribbon flex cable is thin, flat, multiconductor cable that is widely used for internal peripheral connections in electronic systems. In the Logitech Harmony Smart Keyboard, the ribbon flex cable connects the touchpad printed circuit board (PCB) and the keyboard printed circuit board (PCB).
What you need
Step 1
Back Panel
- Turn keyboard over to the backside.
Turn keyboard over to the backside.
1024
Step 2
- Press and slide up on the upper battery latch, using both thumbs.
Press and slide up on the upper battery latch, using both thumbs.
Step 3
- Remove the two AA batteries and set them aside.
Remove the two AA batteries and set them aside.
Step 4
- Unscrew all five 4.0 mm screws, using Phillips #1 screwdriver.
Unscrew all five 4.0 mm screws, using Phillips #1 screwdriver.
Step 5
- Peel off the center sticker to reveal two hidden 4.0 mm screws.
- Unscrew these two screws with a Phillips #1 screwdriver.
Peel off the center sticker to reveal two hidden 4.0 mm screws.
Unscrew these two screws with a Phillips #1 screwdriver.
Step 6
- Lift both top left and top right rubber stickers halfway, using the sharp end of the plastic spudger.
- Unscrew a total of two 4.0 mm screws, under the rubber stickers, using a Phillips #1 screwdriver.
Lift both top left and top right rubber stickers halfway, using the sharp end of the plastic spudger.
Unscrew a total of two 4.0 mm screws, under the rubber stickers, using a Phillips #1 screwdriver.
Step 7
- Unscrew the top center 4.0 mm screw, in the battery compartment, using the Phillips #1 screwdriver.
- Now, you should have a total of ten 4.0 mm screws set aside.
Unscrew the top center 4.0 mm screw, in the battery compartment, using the Phillips #1 screwdriver.
Now, you should have a total of ten 4.0 mm screws set aside.
Step 8
- Wedge the flat end of the spudger between the back panel and front panel.
- Slide the flat end of the spudger from right to left to pry the two panels apart.
Wedge the flat end of the spudger between the back panel and front panel.
Slide the flat end of the spudger from right to left to pry the two panels apart.
Step 9
- Separate the back panel from the front panel completely, using both hands.
- A white ribbon flex cable will remain connected to both panels.
- Pull the panels apart slowly and gently, or the white ribbon flex cable may be unsafely removed.
Separate the back panel from the front panel completely, using both hands.
A white ribbon flex cable will remain connected to both panels.
Pull the panels apart slowly and gently, or the white ribbon flex cable may be unsafely removed.
Step 10
Ribbon Flex Cable
- Grip the lower end of the ribbon flex cable (white band) using your thumb and index finger.
- Then slide the strip out toward yourself in a scooping motion.
- Now, you should have two completely separated panel pieces.
Grip the lower end of the ribbon flex cable (white band) using your thumb and index finger.
Then slide the strip out toward yourself in a scooping motion.
Now, you should have two completely separated panel pieces.
Step 11
- Grip the other lower end of the ribbon flex cable using your thumb and index finger.
- Gently slide the cable up and out of the green card.
Grip the other lower end of the ribbon flex cable using your thumb and index finger.
Gently slide the cable up and out of the green card.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 4 other contributors
Hayley Nichols
Member since: 09/05/2017
507 Reputation
4 Guides authored
Badges:
10
+7 more badges
Team
CSU Fullerton, Team S1-G2, Bruce Fall 2017
Member of CSU Fullerton, Team S1-G2, Bruce Fall 2017
CSUF-BRUCE-F17S1G2
3 Members
10 Guides authored