Difficulty

Easy

Steps

9

Time Required

                          10 - 15 minutes

Sections

1

  • Back Panel
  • 9 steps

Flags

0

  • BackLogitech Harmony Smart Keyboard

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back Panel
  • Turn keyboard over to the backside.

Turn keyboard over to the backside.

1024

Step 2

  • Press and slide up on the upper battery latch, using both thumbs.

Press and slide up on the upper battery latch, using both thumbs.

Step 3

  • Remove the two AA batteries and set them aside.

Remove the two AA batteries and set them aside.

Step 4

  • Unscrew all five 4.0 mm screws, using Phillips #1 screwdriver.

Unscrew all five 4.0 mm screws, using Phillips #1 screwdriver.

Step 5

  • Peel off the center sticker to reveal two hidden 4.0 mm screws.
  • Unscrew these two screws with a Phillips #1 screwdriver.

Peel off the center sticker to reveal two hidden 4.0 mm screws.

Unscrew these two screws with a Phillips #1 screwdriver.

Step 6

  • Lift both top left and top right rubber stickers halfway, using the sharp end of the plastic spudger.
  • Unscrew a total of two 4.0 mm screws, under the rubber stickers, using a Phillips #1 screwdriver.

Lift both top left and top right rubber stickers halfway, using the sharp end of the plastic spudger.

Unscrew a total of two 4.0 mm screws, under the rubber stickers, using a Phillips #1 screwdriver.

Step 7

  • Unscrew the top center 4.0 mm screw, in the battery compartment, using the Phillips #1 screwdriver.
  • Now, you should have a total of ten 4.0 mm screws set aside.

Unscrew the top center 4.0 mm screw, in the battery compartment, using the Phillips #1 screwdriver.

Now, you should have a total of ten 4.0 mm screws set aside.

Step 8

  • Wedge the flat end of the spudger between the back panel and front panel.
  • Slide the flat end of the spudger from right to left to pry the two panels apart.

Wedge the flat end of the spudger between the back panel and front panel.

Slide the flat end of the spudger from right to left to pry the two panels apart.

Step 9

  • Separate the back panel from the front panel completely, using both hands.
  • A white ribbon flex cable will remain connected to both panels.
  • Pull the panels apart slowly and gently, or the white ribbon flex cable may be unsafely removed.

Separate the back panel from the front panel completely, using both hands.

A white ribbon flex cable will remain connected to both panels.

Pull the panels apart slowly and gently, or the white ribbon flex cable may be unsafely removed.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 4 other contributors 


                    Hayley Nichols

Member since: 09/05/2017

507 Reputation

                                      4 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       CSU Fullerton, Team S1-G2, Bruce Fall 2017                        

                                                  Member of CSU Fullerton, Team S1-G2, Bruce Fall 2017 



                    CSUF-BRUCE-F17S1G2                     


                                            3 Members                     


                                            10 Guides authored