Logitech Harmony 950 Motherboard Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          20 minutes

Sections

Battery
4 steps
Motherboard
5 steps

Flags

BackLogitech Harmony 950
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

What you need

Step 1

              Battery

Make sure the remote control is powered off before starting.
Use the Opening Tool to open the port cover at the bottom of the remote control.
Bend the cover back to gain easy access to the screws.

Make sure the remote control is powered off before starting.

Use the Opening Tool to open the port cover at the bottom of the remote control.

Bend the cover back to gain easy access to the screws.

1024

Step 2

Use the Phillips #0 Screwdriver to remove the (2) two 6mm screws.
Pull the bottom cover off of the remote control.

Use the Phillips #0 Screwdriver to remove the (2) two 6mm screws.

Pull the bottom cover off of the remote control.

Step 3

Use the Phillips #1 Screwdriver to remove the (2) two 6mm screws.
There should be a gap on each side to fit the Opening Tool. Use the Opening Tool to open the back cover (Soft Touch cover) using the gap.

Use the Phillips #1 Screwdriver to remove the (2) two 6mm screws.

There should be a gap on each side to fit the Opening Tool. Use the Opening Tool to open the back cover (Soft Touch cover) using the gap.

Step 4

Use the Opening Tool to lift the battery out of the case.
Gently pull the cable out of the socket to unplug the battery.
Be careful not to damage any part of the remote when pulling the cable out.

Use the Opening Tool to lift the battery out of the case.

Gently pull the cable out of the socket to unplug the battery.

Be careful not to damage any part of the remote when pulling the cable out.

Step 5

              Motherboard

Use the Phillips #0 screwdriver to remove the (3) three 6mm screws.
Push the opening tool into the gap along the side of the remote, then slide it across until you hear clicking sounds.
You need to repeat this process for both sides of the remote.

Use the Phillips #0 screwdriver to remove the (3) three 6mm screws.

Push the opening tool into the gap along the side of the remote, then slide it across until you hear clicking sounds.

You need to repeat this process for both sides of the remote.

Step 6

Carefully remove the back cover and place it next to the remote. Be careful not to detach the wire during this process.
Use the Angled Tweezers to carefully pull the white cable end off of the remote and disconnect it.

Carefully remove the back cover and place it next to the remote. Be careful not to detach the wire during this process.

Use the Angled Tweezers to carefully pull the white cable end off of the remote and disconnect it.

Step 7

Use the Phillips #0 screwdriver to remove the (5) five 6mm screws.
Be careful not to detach the pink wires when removing the gold charging conductors.

Use the Phillips #0 screwdriver to remove the (5) five 6mm screws.

Be careful not to detach the pink wires when removing the gold charging conductors.

Step 8

Remove the black tape to access the cable underneath.
Use the Angled Tweezers to lift the black lock.
Slide the yellow cable to disconnect it from the circuit board.

Remove the black tape to access the cable underneath.

Use the Angled Tweezers to lift the black lock.

Slide the yellow cable to disconnect it from the circuit board.

Step 9

Pull the circuit board off of the remote from the bottom, and lift up to detach it from the cover.

Pull the circuit board off of the remote from the bottom, and lift up to detach it from the cover.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 3 other contributors

                    Blake Sanborn

Member since: 09/26/2017

510 Reputation

                                      3 Guides authored                  



                       Badges:
                       15







                                                        +12 more badges

Team

                       USF Tampa, Team S2-G2, Passmore Fall 2017                        

                                                  Member of USF Tampa, Team S2-G2, Passmore Fall 2017 



                    USFT-PASSMORE-F17S2G2                     


                                            4 Members                     


                                            4 Guides authored

عبدالعزيز المناعي - Aug 19, 2019

How replace A Mitsubishi Remote Control

How replace A Mitsubishi Remote Control ?

Thanks

Air conditioning

What you need#

Team#

What you need

Team