Difficulty
Moderate
Steps
11
Time Required
4 minutes
Sections
3
- Battery
- 2 steps
- Motherboard
- 8 steps
- Button Pad
- 1 step
Flags
0
BackLogitech Harmony 900
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Press the oval shaped button on the lower back of the remote to release the battery cover.
- While pressing the button, remove the cover.
Press the oval shaped button on the lower back of the remote to release the battery cover.
While pressing the button, remove the cover.
1024
Step 2
- Push the battery in, pull it up, and slide it out.
Push the battery in, pull it up, and slide it out.
Step 3
Motherboard
- Using tweezers, peel off the sticker located under the battery cover to reveal two screws.
Using tweezers, peel off the sticker located under the battery cover to reveal two screws.
Step 4
- Locate and unscrew the four 50mm screws using the Philips #0 screwdriver.
Locate and unscrew the four 50mm screws using the Philips #0 screwdriver.
Step 5
- Use a credit card to pry the black, plastic, back cover off of the device.
- You may need to get the process started with a metal prying tool before you start using the credit card.
Use a credit card to pry the black, plastic, back cover off of the device.
You may need to get the process started with a metal prying tool before you start using the credit card.
Step 6
- Locate the three 50mm screws on the back of the remote and remove them using the Phillips #0 screwdriver.
Locate the three 50mm screws on the back of the remote and remove them using the Phillips #0 screwdriver.
Step 7
- Pry the black, front face of the remote from the back silver part by inserting a credit card in between and sliding down.
- Again, you may need to use a metal prying tool to get the separation started.
Pry the black, front face of the remote from the back silver part by inserting a credit card in between and sliding down.
Again, you may need to use a metal prying tool to get the separation started.
Step 8
- When you look at the circuit board, you should see a ribbon attaching the board to the plastic casing.
- A little lever is holding the ribbon in place. Lift the lever with your nail or a 2.5mm flat-head screwdriver. Move the ribbon away from the circuit board.
When you look at the circuit board, you should see a ribbon attaching the board to the plastic casing.
A little lever is holding the ribbon in place. Lift the lever with your nail or a 2.5mm flat-head screwdriver. Move the ribbon away from the circuit board.
Step 9
- Using the Philips #0 screwdriver, remove the three 50mm screws from the circuit board.
Using the Philips #0 screwdriver, remove the three 50mm screws from the circuit board.
Step 10
- Using your hands, carefully separate the motherboard from the rest of the remote.
Using your hands, carefully separate the motherboard from the rest of the remote.
Step 11
Button Pad
- Peel off the button pads from the device frame.
Peel off the button pads from the device frame.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 2 other contributors
Tyler Hanks
Member since: 09/25/2017
442 Reputation
3 Guides authored
Badges:
6
+3 more badges
Team
USF Tampa, Team S4-G5, Eyestone Fall 2017
Member of USF Tampa, Team S4-G5, Eyestone Fall 2017
USFT-EYESTONE-F17S4G5
4 Members
4 Guides authored
