Difficulty
Moderate
Steps
9
Time Required
7 minutes
Sections
2
- Case
- 7 steps
- Motherboard
- 2 steps
Flags
0
BackLogitech Harmony 650
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Case
- Remove the battery cover by applying pressure to the indented area and pushing the cover toward the rear of the device.
Remove the battery cover by applying pressure to the indented area and pushing the cover toward the rear of the device.
1024
Step 2
- Remove the batteries using the silver pull tab.
Remove the batteries using the silver pull tab.
Step 3
- Using a J000 Philips head screwdriver remove the four 5mm screws around the rim of the battery chamber.
Using a J000 Philips head screwdriver remove the four 5mm screws around the rim of the battery chamber.
Step 4
- Remove the small plastic cover beneath the plastic LED housing by using a 3.0 flathead screwdriver and a spudger to pry it off. It is glued to the case. If you are having trouble removing it try applying some heat to loosen the glue.
Remove the small plastic cover beneath the plastic LED housing by using a 3.0 flathead screwdriver and a spudger to pry it off. It is glued to the case. If you are having trouble removing it try applying some heat to loosen the glue.
Step 5
- Remove the two 5mm screws located underneath the cover using a J000 Philips screwdriver bit.
Remove the two 5mm screws located underneath the cover using a J000 Philips screwdriver bit.
Step 6
- Using a plastic opening tool, pry the case off starting from the top of the device (nearest the transmitter). There are 3 tabs along the side of the case and one at the back.
- The top led protector plastic cover will also be freed once back is removed.
Using a plastic opening tool, pry the case off starting from the top of the device (nearest the transmitter). There are 3 tabs along the side of the case and one at the back.
The top led protector plastic cover will also be freed once back is removed.
Step 7
- Remove the rear cover.
Remove the rear cover.
Step 8
Motherboard
- Using a J0 screwdriver remove the three 5mm screws holding the motherboard to the front face. Two are located just below the processor in the middle of the device and the third is located at the very bottom.
Using a J0 screwdriver remove the three 5mm screws holding the motherboard to the front face. Two are located just below the processor in the middle of the device and the third is located at the very bottom.
Step 9
- Remove the motherboard by gently pulling it away from the case.
Remove the motherboard by gently pulling it away from the case.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
9 other people completed this guide.
Author
with 4 other contributors
Connor Gallagher
Member since: 01/11/2016
998 Reputation
5 Guides authored
Badges:
11
+8 more badges
Team
Eastern Washington University, Team 1-2, Rowley Winter 2016
Member of Eastern Washington University, Team 1-2, Rowley Winter 2016
EWU-ROWLEY-W16S1G2
4 Members
5 Guides authored
tedcmacdonald - Aug 9, 2016
Reply
Thanks! Remote was dropped in water tonight & I used this to take it apart for a thorough drying out.
howardgis - Dec 21, 2016
Reply
anyone know where I can purchase the motherboard for this model? Logitech does not sell them
Chris Phillips - Aug 5, 2020
I assume nobody sells the motherboard as a spare part? Pity, mine 650’s dead!
Gia-khanh Nguyen - Oct 3, 2018
Reply
Thank you so much for the instructions. Some buttons of my Harmony 650 were not responding and I was able to open it and clean with alcohol the rubber pins and their peer circuit board conductor traces. After that all works as new !