Difficulty

Moderate

Steps

11

Time Required

                          15 minutes

Sections

1

  • Ribbon Cable
  • 11 steps

Flags

0

  • BackLogitech Circle Home Monitor

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Ribbon Cable
  • Wedge the plastic opening tool under the black circle lens and gently pry it off.
  • The lens is only attached with sticky tape and should remove relatively easily.

Wedge the plastic opening tool under the black circle lens and gently pry it off.

The lens is only attached with sticky tape and should remove relatively easily.

1024

Step 2

  • Remove the four 3mm Phillips #0 screws that hold down the first ring.

Remove the four 3mm Phillips #0 screws that hold down the first ring.

Step 3

  • Remove the four 3mm Phillips #0 screws that hold down the second ring.

Remove the four 3mm Phillips #0 screws that hold down the second ring.

Step 4

  • Remove the four 3mm Phillips #0 screws that hold down the final ring. Do not remove the lens/battery bundle yet.
  • The lens/battery bundle is attached to the base by a ribbon cable that can break, so be very careful handling the circle.

Remove the four 3mm Phillips #0 screws that hold down the final ring. Do not remove the lens/battery bundle yet.

The lens/battery bundle is attached to the base by a ribbon cable that can break, so be very careful handling the circle.

Step 5

  • Gently remove the lens/battery bundle from the base of the circle, being mindful of the ribbon cable.

Gently remove the lens/battery bundle from the base of the circle, being mindful of the ribbon cable.

Step 6

  • Gently pull the ribbon cable loose from the lens/battery bundle.
  • While this is not an entirely necessary step, it helps to ensure the ribbon cable will not break during the rest of the replacement.

Gently pull the ribbon cable loose from the lens/battery bundle.

While this is not an entirely necessary step, it helps to ensure the ribbon cable will not break during the rest of the replacement.

Step 7

  • Once the old ribbon cable has been detached from the lens/battery bundle it’s time to release the other side from the base.
  • Locate the screws holding the base together by feeling for the soft spots underneath the manufacturer’s sticker. Punch through with your screwdriver and remove the three 3mm Phillips #0 screws.
  • The two pieces of the base can now be easily pulled apart.

Once the old ribbon cable has been detached from the lens/battery bundle it’s time to release the other side from the base.

Locate the screws holding the base together by feeling for the soft spots underneath the manufacturer’s sticker. Punch through with your screwdriver and remove the three 3mm Phillips #0 screws.

The two pieces of the base can now be easily pulled apart.

Step 8

  • Gently pull the ribbon cable loose from its connection to the base.

Gently pull the ribbon cable loose from its connection to the base.

Step 9

  • Slide the push pin holding the plastic connector/ribbon cable in place out on both sides.

Slide the push pin holding the plastic connector/ribbon cable in place out on both sides.

Step 10

  • Remove the black plastic connector and the two springs from the base of the device.

Remove the black plastic connector and the two springs from the base of the device.

Step 11

  • Reach inside the circle and pull the ribbon cable free from the device.

Reach inside the circle and pull the ribbon cable free from the device.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Haley Williams

Member since: 09/28/2017

112 Reputation

                                      1 Guide authored                  



                       Badges:
                       2

Team

                       University of Maine, Team S1-G4, Diaz Fall 2017                        

                                                  Member of University of Maine, Team S1-G4, Diaz Fall 2017 



                    UMAINE-DIAZ-F17S1G4                     


                                            3 Members                     


                                            7 Guides authored

Nico Kersop - Feb 10, 2018

Reply

where can I buy such a cable?

kersop@gmail.com

Helen - Feb 19, 2018

Reply

The cable I received from China is not the right one. Where do you buy the correct one?

Michele Ingratta - Apr 4, 2018

Reply

Can you advise where to buy the correct cable?

Alican Döşlü - Sep 23, 2019

Reply

I have cable has beark off. I need that cable.

Where can I find

l_samin - Mar 29, 2020

Reply

i also need that cable