Difficulty

Easy

Steps

8

Time Required

                          15 minutes

Sections

1

  • Battery
  • 8 steps

Flags

0

  • BackLogitech Circle Home Monitor

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Wedge the plastic opening tool under the black circle lens to gently pry it off.
  • The lens is only attached with sticky tape and should remove relatively easily.

Wedge the plastic opening tool under the black circle lens to gently pry it off.

The lens is only attached with sticky tape and should remove relatively easily.

1024

Step 2

  • Remove the four 3mm Phillips #0 screws that hold down the first ring.

Remove the four 3mm Phillips #0 screws that hold down the first ring.

Step 3

  • Remove the four 3mm Phillips #0 screws that hold down the second ring.

Remove the four 3mm Phillips #0 screws that hold down the second ring.

Step 4

  • Remove the four 3mm Phillips #0 screws that hold down the final ring. Do not remove the lens/battery bundle yet.
  • The lens/battery bundle is attached to the base by a ribbon cable that can break, so be very careful handling the circle.

Remove the four 3mm Phillips #0 screws that hold down the final ring. Do not remove the lens/battery bundle yet.

The lens/battery bundle is attached to the base by a ribbon cable that can break, so be very careful handling the circle.

Step 5

  • Gently remove the lens/battery bundle from the base of the circle, being mindful of the ribbon cable.

Gently remove the lens/battery bundle from the base of the circle, being mindful of the ribbon cable.

Step 6

  • Gently pull the ribbon cable loose from the lens/battery bundle.
  • While this is not an entirely necessary step, it helps to ensure the ribbon cable will not break during the rest of the battery replacement.

Gently pull the ribbon cable loose from the lens/battery bundle.

While this is not an entirely necessary step, it helps to ensure the ribbon cable will not break during the rest of the battery replacement.

Step 7

  • Carefully unplug the battery from the rest of the lens.

Carefully unplug the battery from the rest of the lens.

Step 8

  • Remove the battery using a plastic opening tool. The battery is attached with sticky tape and will remove with gentle prying motions.

Remove the battery using a plastic opening tool. The battery is attached with sticky tape and will remove with gentle prying motions.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.

Author

                                      with 1 other contributor 


                    Kylie

Member since: 09/28/2017

291 Reputation

                                      1 Guide authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       University of Maine, Team S1-G4, Diaz Fall 2017                        

                                                  Member of University of Maine, Team S1-G4, Diaz Fall 2017 



                    UMAINE-DIAZ-F17S1G4                     


                                            3 Members                     


                                            7 Guides authored

Diane Fischer - Jul 16, 2019

Reply

What about circle wireless batter with the unscrewBle lens? I keep getting error in set up that the battery is too low to proceed.

I charged only the battery portion all day. Stil. Same results

Mike Arango - Dec 7, 2022

Did you figure out the battery?

Razvan Ciocanel - Aug 28, 2019

Reply

Where did you buy the battery? I can’t find something to replace it with :(

Jonathan Flower - Dec 9, 2019

Reply

I measured my battery and it is 40mm x 14mm x 30mm. The space for the battery looks like I can fit something as long as 45mm. I can not find anything in the US. Going to try these: https://www.ebay.com/itm/3-7V-1200mAh-10…. Pretty annoying that I can not find something to drop in. The most challenging part of this repair is going to be wiring these two Lipos together properly. Does anyone know the voltage of the 3 wires? My battery is completely dead so I cannot get a voltage reading. I am going to have to plug the camera in, plug the battery connector in and get the voltage from there :)

Razvan Ciocanel - Jan 25, 2020

Hey, did you manage to make this work? I want to order some battery and try the same thing. I understand that you need 2 from the pictures. How are they tied together? You can not see that from this tutorial.