Difficulty
Difficult
Steps
12
Time Required
15 - 30 minutes
Sections
4
- Chassis
- 6 steps
- Disc Tray
- 1 step
- Disc Tray Belt
- 1 step
- Eject Button and Power LED Light
- 4 steps
Flags
1
Better Introduction
Improve this guide by completing or revising its introduction.
BackLite-On iHAS324
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Chassis
- Insert a paper clip into a small hole on the right side of the faceplate bellow the disc tray.
- There may be resistance, do not be afraid to use force.
- The tray should then pop open.
- Pull out the tray so that it is fully extended.
Insert a paper clip into a small hole on the right side of the faceplate bellow the disc tray.
There may be resistance, do not be afraid to use force.
The tray should then pop open.
Pull out the tray so that it is fully extended.
1024
Step 2
- Use a plastic opening tool to push the three tabs located on the right, left, and bottom side of the outer chassis to loosen the faceplate off.
Use a plastic opening tool to push the three tabs located on the right, left, and bottom side of the outer chassis to loosen the faceplate off.
Step 3
- Pull the faceplate off the chassis.
- Do NOT pull the faceplate all the way off the disc tray, because doing so can cause damage to the faceplate.
- There may be resistance, do not be afraid to use force.
Pull the faceplate off the chassis.
Do NOT pull the faceplate all the way off the disc tray, because doing so can cause damage to the faceplate.
Step 4
- Using the Phillips Head #2 screwdriver, unscrew the two 8.5 mm screws located on the bottom back of the chassis.
Using the Phillips Head #2 screwdriver, unscrew the two 8.5 mm screws located on the bottom back of the chassis.
Step 5
- Remove the bottom plate by lifting it off the device.
Remove the bottom plate by lifting it off the device.
Step 6
- Turn the device over.
- Remove the top plate by pulling the sides and lifting the plate off.
Turn the device over.
Remove the top plate by pulling the sides and lifting the plate off.
Step 7
Disc Tray
- Push the left tab in and slide the tray out on the left side.
- Pull the gray plastic casing on the right side away from the tray.
- Slide the right side of the tray out.
Push the left tab in and slide the tray out on the left side.
Pull the gray plastic casing on the right side away from the tray.
Slide the right side of the tray out.
Step 8
Disc Tray Belt
- Take tweezers and remove the black tray belt from the gears carefully.
Take tweezers and remove the black tray belt from the gears carefully.
Step 9
Eject Button and Power LED Light
- Flip the device over.
Flip the device over.
Step 10
- Use a plastic opening tool to pull all three tabs, lifting up the circuit board as you go.
Use a plastic opening tool to pull all three tabs, lifting up the circuit board as you go.
Step 11
- Carefully lift the circuit board out of the plastic casing.
Carefully lift the circuit board out of the plastic casing.
Step 12
- Using a solder wick, unsolder either the eject button or Power LED Light. Soldering Guide
- Then, using a solder iron, replace them.
Using a solder wick, unsolder either the eject button or Power LED Light. Soldering Guide
Then, using a solder iron, replace them.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Kayla Culpepper
Member since: 03/22/2015
675 Reputation
5 Guides authored
Badges:
10
+7 more badges
Team
Baylor, Team 5-9, Williams Spring 2015
Member of Baylor, Team 5-9, Williams Spring 2015
BU-WILLIAMS-S15S5G9
3 Members
5 Guides authored
