Difficulty
Moderate
Steps
12
Time Required
15 - 30 minutes
Sections
2
- Disassembling LG VX8300 Body
- 5 steps
- Screen Housing Replacement
- 7 steps
Flags
0
BackLG VX8300
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Disassembling LG VX8300 Body
- Power off the device by holding down the red button labeled PWR.
- Be sure that the phone is powered off before touching the battery to avoid danger.
- Remove the battery pack cover by pushing down on the solid lines at the top end of the cover. Slide the cover down while applying the pushing force at the top to remove the cover completely.
Power off the device by holding down the red button labeled PWR.
Be sure that the phone is powered off before touching the battery to avoid danger.
Remove the battery pack cover by pushing down on the solid lines at the top end of the cover. Slide the cover down while applying the pushing force at the top to remove the cover completely.
1024
Step 2
- Place your finger into the semicircle gap on top of the battery.
- Apply force downward and out, so the battery pops out of the phone.
Place your finger into the semicircle gap on top of the battery.
Apply force downward and out, so the battery pops out of the phone.
Step 3
- Locate the two rubber pads covering the screws at the top of the phone near the hinge.
- Use tweezers to lift and remove the rubber pads.
Locate the two rubber pads covering the screws at the top of the phone near the hinge.
Use tweezers to lift and remove the rubber pads.
Step 4
- Use a Phillips #00 screwdriver to remove all four 3mm screws from the back of the phone.
Use a Phillips #00 screwdriver to remove all four 3mm screws from the back of the phone.
Step 5
- Use your fingers to gently separate the front plate from the phone. You may need to slide a plastic opening tool along the crevice between the faces to separate it more easily.
- Remove the casing after it has been detached. The logic board is now fully accessible.
- Once the body case is removed, the volume and camera buttons move freely. Ensure all loose pieces remain accounted for.
Use your fingers to gently separate the front plate from the phone. You may need to slide a plastic opening tool along the crevice between the faces to separate it more easily.
Remove the casing after it has been detached. The logic board is now fully accessible.
Once the body case is removed, the volume and camera buttons move freely. Ensure all loose pieces remain accounted for.
Step 6
Screen Housing Replacement
- Use a plastic opening tool to gently lift the motherboard out of the case. The board is secured by six holes around the perimeter and will become free when pried from the supports.
Use a plastic opening tool to gently lift the motherboard out of the case. The board is secured by six holes around the perimeter and will become free when pried from the supports.
Step 7
- Remove the ribbon cable by lifting up the orange rectangle in the middle-top portion of the exposed device.
Remove the ribbon cable by lifting up the orange rectangle in the middle-top portion of the exposed device.
Step 8
- Hold the phone securely in your left hand by placing your thumb on the hinge and wrapping your fingers around the back of the device.
- Pinch the right flange near the flip hinge with the right hand and apply pressure.
- Continue applying pressure until the two halves separate. Pull the bottom half towards you.
Hold the phone securely in your left hand by placing your thumb on the hinge and wrapping your fingers around the back of the device.
Pinch the right flange near the flip hinge with the right hand and apply pressure.
Continue applying pressure until the two halves separate. Pull the bottom half towards you.
Step 9
- Separate the keyboard from its housing.
- Slide the ribbon cable out through the uppermost slot in the housing.
Separate the keyboard from its housing.
Slide the ribbon cable out through the uppermost slot in the housing.
Step 10
- Remove the four rubber screw covers with tweezers located on the corners of the internal screen.
- Remove all four 2 by 3 mm Phillips screws located under the rubber pads using a Phillips #00 screwdriver.
Remove the four rubber screw covers with tweezers located on the corners of the internal screen.
Remove all four 2 by 3 mm Phillips screws located under the rubber pads using a Phillips #00 screwdriver.
Step 11
- Guide the spudger along the seam line of the phone screen to slowly separate the two pieces.
Guide the spudger along the seam line of the phone screen to slowly separate the two pieces.
Step 12
- Separate the external screen housing with your hands.
- Replace the old screen housing with a new one and snap it together to complete the replacement.
Separate the external screen housing with your hands.
Replace the old screen housing with a new one and snap it together to complete the replacement.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 6 other contributors
Oscar
Member since: 03/17/2015
204 Reputation
1 Guide authored
Badges:
8
+5 more badges
Team
UMass Dartmouth, Team 3-7, Duarte Spring 2015
Member of UMass Dartmouth, Team 3-7, Duarte Spring 2015
UMASSD-DUARTE-S15S3G7
3 Members
10 Guides authored