Difficulty
Moderate
Steps
13
Time Required
15 - 30 minutes
Sections
3
- Battery
- 2 steps
- Plastic Screen Protector
- 4 steps
- LCD Screens
- 7 steps
Flags
1
Inconsistent Images
Updating the images on this guide to be more consistent with the prerequisites would increase its awesomeness.
BackLG VX5600
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Hold your phone with the back casing facing you and the bottom of the phone towards the sky.
- Push down on the cover and slide down to remove. You should only have to apply minimal pressure.
Hold your phone with the back casing facing you and the bottom of the phone towards the sky.
Push down on the cover and slide down to remove. You should only have to apply minimal pressure.
1024
Step 2
- Insert your finger into the small indentation above the battery.
- Push down on the battery and pull it away from the phone; it will pop out.
Insert your finger into the small indentation above the battery.
Push down on the battery and pull it away from the phone; it will pop out.
Step 3
Plastic Screen Protector
- Use tweezers to remove the two rubber covers found at the left and right corners below the inside screen.
Use tweezers to remove the two rubber covers found at the left and right corners below the inside screen.
Step 4
- Grasp the phone and rotate it 90 degrees counterclockwise for a better grip.
- Unscrew the two 3.0-mm Phillips #000 screws, found under the rubber covers at the bottom left and right corners.
- Some of the pictures show the bottom of the phone disassembled. It is unneccessary to disassemble the bottom of the phone for this guide.
Grasp the phone and rotate it 90 degrees counterclockwise for a better grip.
Unscrew the two 3.0-mm Phillips #000 screws, found under the rubber covers at the bottom left and right corners.
Some of the pictures show the bottom of the phone disassembled. It is unneccessary to disassemble the bottom of the phone for this guide.
Step 5
- Hold the opened phone upright.
- Use the spudger to pry around the edges of the phone and detach the tabs.
- Make sure all the tabs around the grey cover are detached. They are located on the top and on both sides of the screen.
Hold the opened phone upright.
Use the spudger to pry around the edges of the phone and detach the tabs.
Make sure all the tabs around the grey cover are detached. They are located on the top and on both sides of the screen.
Step 6
- Use your finger to lift up the grey plastic cover.
- Use the tweezers to grasp the plastic screen, and pull the plastic screen protector up and out of the phone.
- The plastic screen protector is adhered with glue to the back of the phone, so a little force is required to remove it.
Use your finger to lift up the grey plastic cover.
Use the tweezers to grasp the plastic screen, and pull the plastic screen protector up and out of the phone.
The plastic screen protector is adhered with glue to the back of the phone, so a little force is required to remove it.
Step 7
LCD Screens
- Use one hand to grasp the phone and prop the inner grey casing up.
- Unscrew the two 3.0-mm Phillips #000 screws located in the upper left and right hand corners.
Use one hand to grasp the phone and prop the inner grey casing up.
Unscrew the two 3.0-mm Phillips #000 screws located in the upper left and right hand corners.
Step 8
- Using your hands hold the inner grey casing up and pull on the black plastic that surrounds the screen away from the outer grey casing.
- The black plastic piece is attached with glue and two wires to the outer grey casing, so you will not be able to completely separate the plastic pieces yet.
Using your hands hold the inner grey casing up and pull on the black plastic that surrounds the screen away from the outer grey casing.
The black plastic piece is attached with glue and two wires to the outer grey casing, so you will not be able to completely separate the plastic pieces yet.
Step 9
- Using tweezers, pull the vibration motor away from the outer grey casing and towards the black plastic surrounding the screens.
- The vibration motor is adhered with glue, so it may take some force to pry it off of the outer grey casing of the phone.
Using tweezers, pull the vibration motor away from the outer grey casing and towards the black plastic surrounding the screens.
The vibration motor is adhered with glue, so it may take some force to pry it off of the outer grey casing of the phone.
Step 10
- Flip the phone closed so that the top outer casing is facing you.
- Lift up on the the outer grey casing, completely removing it from the phone.
Flip the phone closed so that the top outer casing is facing you.
Lift up on the the outer grey casing, completely removing it from the phone.
Step 11
- Remove the green tape that covers the end of the yellow flex cable.
Remove the green tape that covers the end of the yellow flex cable.
Step 12
- Grasp the phone with one hand, and use the tweezers with the other hand to pull up on the flex cable disconnecting it from the screen.
Grasp the phone with one hand, and use the tweezers with the other hand to pull up on the flex cable disconnecting it from the screen.
Step 13
- Use your fingers to lift up the detached flex cable and use the tweezers to lift the LCD screen component out of the phone casing.
- The speakers and vibration motor will still be attached to the screen component. These are soldered onto the screens and are installed as a single unit.
Use your fingers to lift up the detached flex cable and use the tweezers to lift the LCD screen component out of the phone casing.
The speakers and vibration motor will still be attached to the screen component. These are soldered onto the screens and are installed as a single unit.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
3 other people completed this guide.
Author
with 4 other contributors
Jessica Bradley
Member since: 06/04/2013
279 Reputation
2 Guides authored
Badges:
10
+7 more badges
Team
University of Kentucky Louisville, Team 1-5, Chamberlain Spring 2013
Member of University of Kentucky Louisville, Team 1-5, Chamberlain Spring 2013
LOUISVILLE-CHAMBERLAIN-S13S1G5
2 Members
12 Guides authored
Bil Heybruck - Feb 16, 2016
Reply
just swapped screens Perfect. step 5 is harder than it look but take time and go easy, I used a 1/8 in blade screwdriver.