Difficulty
Moderate
Steps
10
Time Required
15 - 20 minutes
Sections
4
- Rear Glass
- 3 steps
- Motherboard
- 5 steps
- Battery
- 1 step
- Front-Facing Camera
- 1 step
Flags
0
BackLG V30 Plus
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Rear Glass
- Use a pair of iOpeners by heating them in a microwave and placing the hot pads on the edges of the phone.
- Allow to sit for 1-2 minutes to heat up the adhesive.
- A heat gun may need to be used if you have trouble separating the backing in the next step.
Use a pair of iOpeners by heating them in a microwave and placing the hot pads on the edges of the phone.
Allow to sit for 1-2 minutes to heat up the adhesive.
A heat gun may need to be used if you have trouble separating the backing in the next step.
1024
Step 2
- Insert an Opening Tool into the seam between the rear glass and side of the phone.
- Pry the glass off just enough to insert an Opening Pick.
- Slide the Opening Tool around the edges of the device, placing Opening Picks regularly.
Insert an Opening Tool into the seam between the rear glass and side of the phone.
Pry the glass off just enough to insert an Opening Pick.
Slide the Opening Tool around the edges of the device, placing Opening Picks regularly.
Step 3
- Once all edges of the device are lifted free, use a Suction Handle to gently pull the rear glass off the device.
Once all edges of the device are lifted free, use a Suction Handle to gently pull the rear glass off the device.
Step 4
Motherboard
- Remove the ten 4mm screws using the Phillips #00 Screwdriver.
Remove the ten 4mm screws using the Phillips #00 Screwdriver.
Step 5
- Gently push down on the small black tab with a Spudger to release the protective board.
- Slide an Opening Tool between the phone and the protective board and slide along the edges of the phone to unclip it.
- Carefully wiggle the board back and forth while gently pulling to unclip the last attachment point.
Gently push down on the small black tab with a Spudger to release the protective board.
Slide an Opening Tool between the phone and the protective board and slide along the edges of the phone to unclip it.
Carefully wiggle the board back and forth while gently pulling to unclip the last attachment point.
Step 6
- Slide an Opening Tool between the lower protective board and the phone to unclip.
- Slide the tool along the remaining edges of the protective board until it pops off.
Slide an Opening Tool between the lower protective board and the phone to unclip.
Slide the tool along the remaining edges of the protective board until it pops off.
Step 7
- Gently pry each visible ribbon cable away from the motherboard to disconnect them.
Gently pry each visible ribbon cable away from the motherboard to disconnect them.
Step 8
- Gently remove the motherboard from the phone.
Gently remove the motherboard from the phone.
Step 9
Battery
- Use a Spudger to get between the battery and the phone and pry each edge of the battery away from the board.
- There may be a strong adhesive under the battery, so work your way around the battery carefully and slowly.
- Insert Opening Picks if needed to keep the battery elevated.
Use a Spudger to get between the battery and the phone and pry each edge of the battery away from the board.
There may be a strong adhesive under the battery, so work your way around the battery carefully and slowly.
Insert Opening Picks if needed to keep the battery elevated.
Step 10
Front-Facing Camera
- Use a Spudger to pry away the front-facing camera from the board.
Use a Spudger to pry away the front-facing camera from the board.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 4 other contributors
Samuel Jahnke
Member since: 04/22/2019
279 Reputation
2 Guides authored
Badges:
8
+5 more badges
Team
Cal Poly, Team S1-G3, Maness Spring 2019
Member of Cal Poly, Team S1-G3, Maness Spring 2019
CPSU-MANESS-S19S1G3
4 Members
10 Guides authored