Difficulty
Moderate
Steps
11
Time Required
30 minutes - 1 hour
Sections
1
- Screen
- 11 steps
Flags
0
BackLG K7
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Screen
- Place phone face-down and use your nail to pry the back off the back.
Place phone face-down and use your nail to pry the back off the back.
1024
Step 2
- Use a plastic spudger or your nail to lift the battery out of the device and put it aside.
- The battery should come out with little effort. If it does not, do not force it.
Use a plastic spudger or your nail to lift the battery out of the device and put it aside.
The battery should come out with little effort. If it does not, do not force it.
Step 3
- Use a Phillips #0 screwdriver to remove the single 3.5mm screw holding the power button and volume rocker in place and lift it out and put it to the side.
Use a Phillips #0 screwdriver to remove the single 3.5mm screw holding the power button and volume rocker in place and lift it out and put it to the side.
Step 4
- Use a Phillips #0 screwdriver to unscrew the three 3.5mm screws in the bottom portion of the phone and put them to the side.
- Use a spudger to pry the plastic bit off. Be warned, it will pop out and might fling itself when you attempt to pry it out.
Use a Phillips #0 screwdriver to unscrew the three 3.5mm screws in the bottom portion of the phone and put them to the side.
Use a spudger to pry the plastic bit off. Be warned, it will pop out and might fling itself when you attempt to pry it out.
Step 5
- Use a spudger to pry the plastic bit off.
- Warning, it will snap out and might fling itself when you attempt to pry it out.
Use a spudger to pry the plastic bit off.
Warning, it will snap out and might fling itself when you attempt to pry it out.
Step 6
- Use a Phillips #0 screwdriver to unscrew the five 3.5mm screws holding the housing into the device.
- Use a spudger to pop it out of the back of the device exposing the motherboard.
Use a Phillips #0 screwdriver to unscrew the five 3.5mm screws holding the housing into the device.
Use a spudger to pop it out of the back of the device exposing the motherboard.
Step 7
- Use a plastic spudger to lift the motherboard out of the casing.
- You must use a plastic tool for this step or you may risk damaging the motherboard.
Use a plastic spudger to lift the motherboard out of the casing.
You must use a plastic tool for this step or you may risk damaging the motherboard.
Step 8
- Turn the device over and locate the connector between the digitizer and the motherboard.
- Use a plastic spudger to disconnect the connector.
Turn the device over and locate the connector between the digitizer and the motherboard.
Use a plastic spudger to disconnect the connector.
Step 9
- Turn the screen housing over and use a hair dryer to heat the screen.
- This melts the adhesive between the screen and the housing, allowing you to separate the two.
- Be sure to evenly heat the screen and take care not to burn yourself.
Turn the screen housing over and use a hair dryer to heat the screen.
This melts the adhesive between the screen and the housing, allowing you to separate the two.
Be sure to evenly heat the screen and take care not to burn yourself.
Step 10
- Once the screen is heated, use a plastic spudger to attempt to peel the glass away from the housing.
- This will take some time, so take care not to break the glass.
- Once the spudger is under the glass, drag it around the edge and separate the glass and the housing.
Once the screen is heated, use a plastic spudger to attempt to peel the glass away from the housing.
This will take some time, so take care not to break the glass.
Once the spudger is under the glass, drag it around the edge and separate the glass and the housing.
Step 11
- You have now successfully removed the screen and digitizer from the housing.
You have now successfully removed the screen and digitizer from the housing.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
8 other people completed this guide.
Author
with 2 other contributors
Christopher Chheng
Member since: 11/01/2018
559 Reputation
2 Guides authored
Badges:
7
+4 more badges
Team
IUPUI, Team S3-G4, Harley Fall 2018
Member of IUPUI, Team S3-G4, Harley Fall 2018
IUPUI-HARLEY-F18S3G4
3 Members
4 Guides authored