Difficulty
Moderate
Steps
13
Time Required
25 - 35 minutes
Sections
5
- Back Cover
- 2 steps
- Battery
- 2 steps
- Loudspeaker
- 3 steps
- Motherboard Cover Assembly
- 3 steps
- Power & Volume Button Cable
- 3 steps
Flags
1
Member-Contributed Guide
An awesome member of our community made this guide. It is not managed by iFixit staff.
BackLG G3
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Cover
- Power off your phone before beginning disassembly.
- Insert a thumbnail, or a prying tool like a spudger, into the notch at the bottom left of the back cover.
- Pry the back cover up to separate its plastic clips.
Power off your phone before beginning disassembly.
Insert a thumbnail, or a prying tool like a spudger, into the notch at the bottom left of the back cover.
Pry the back cover up to separate its plastic clips.
1024
Step 2
- Lift the back cover to release the rest of the plastic clips and remove it.
- In case you can’t lift the back cover completely, slide your fingernail or your prying tool around the midframe to release the remaining clips.
- To reinstall the back cover, press it firmly into place until you hear a snap from the plastic clips to form a seamless connection with the rear side of the phone.
Lift the back cover to release the rest of the plastic clips and remove it.
In case you can’t lift the back cover completely, slide your fingernail or your prying tool around the midframe to release the remaining clips.
To reinstall the back cover, press it firmly into place until you hear a snap from the plastic clips to form a seamless connection with the rear side of the phone.
Step 3
Battery
- Use a fingernail or a prying tool at the marked notch to lever the battery out of its recess.
Use a fingernail or a prying tool at the marked notch to lever the battery out of its recess.
Step 4
- Lift the battery out of its recess and remove it.
Lift the battery out of its recess and remove it.
Step 5
Loudspeaker
- Remove the four Phillips #00 screws (4 mm length).
Remove the four Phillips #00 screws (4 mm length).
Step 6
- Insert a thumbnail, or a prying tool like a spudger, into the notch at the bottom left of the back cover you used earlier to remove the back cover.
- Pry up the plastic panel, including the loudspeaker, until you can get a good grip.
Insert a thumbnail, or a prying tool like a spudger, into the notch at the bottom left of the back cover you used earlier to remove the back cover.
Pry up the plastic panel, including the loudspeaker, until you can get a good grip.
Step 7
- Carefully remove the plastic panel including the loudspeaker by gently pulling it away from the phone assembly.
Carefully remove the plastic panel including the loudspeaker by gently pulling it away from the phone assembly.
Step 8
Motherboard Cover Assembly
- Remove the eight Phillips #00 screws (4 mm length).
Remove the eight Phillips #00 screws (4 mm length).
Step 9
- Insert an opening pick between the bottom right corner of the motherboard cover and the motherboard.
- Pry up the motherboard cover to open the plastic clips which hold the cover in its place.
- The clips can be a bit resistive. If you’re having trouble prying up the motherboard cover, slightly rotate the opening pick sideways to make the process easier.
- Work your way along the right edge.
Insert an opening pick between the bottom right corner of the motherboard cover and the motherboard.
Pry up the motherboard cover to open the plastic clips which hold the cover in its place.
The clips can be a bit resistive. If you’re having trouble prying up the motherboard cover, slightly rotate the opening pick sideways to make the process easier.
Work your way along the right edge.
Step 10
- Carefully lift the right edge of the motherboard cover.
- The remaining plastic clips should open during this process or can be unhinged easily by hand.
- Remove the motherboard assembly.
Carefully lift the right edge of the motherboard cover.
The remaining plastic clips should open during this process or can be unhinged easily by hand.
Remove the motherboard assembly.
Step 11
Power & Volume Button Flex Cable
- Remove the last screw attaching the rear camera lens to the frame.
- Now use a plastic spudger to carefully remove the camera lens.
Remove the last screw attaching the rear camera lens to the frame.
Now use a plastic spudger to carefully remove the camera lens.
Step 12
- Using the spudger, release power & volume button flex from adhesive carefully.
Using the spudger, release power & volume button flex from adhesive carefully.
Step 13
- Finally, remove the flex.
Finally, remove the flex.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
9 other people completed this guide.
Author
with 5 other contributors
Sophia
Member since: 03/25/2014
43,666 Reputation
62 Guides authored
Badges:
26
+23 more badges
mitoll - Jan 15, 2018
Reply
I bought a more powerful battery. 6800 mah .instead of the 3000mah OEM . Ia there any problem using it?