Lg G2 Sprint Rear Facing Camera Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

Suggest a time??

Sections

Charger Port
7 steps
Rear Camera
1 step

Flags

Incorrect Tools

Help make this guide better by using the correct tools in images and/or text.

BackLG G2 Sprint
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Charger Port

Use a plastic opening tool to pry open your phone case. Flip the phone over and start by sliding your tool between the two sides of your phone case. Work the tool towards the bottom of the phone case, gently prying the case open. There is a clip that will pop open after applying gentle but consistent pressure.
Make sure to release the clip on the top left corner of the phone case carefully. This is usually the most difficult clip to release.

Use a plastic opening tool to pry open your phone case. Flip the phone over and start by sliding your tool between the two sides of your phone case. Work the tool towards the bottom of the phone case, gently prying the case open. There is a clip that will pop open after applying gentle but consistent pressure.

Make sure to release the clip on the top left corner of the phone case carefully. This is usually the most difficult clip to release.

1024

Step 2

After removing the outer phone case, you will need two Phillips head bits. One J0 and one J000 size.
There are 11 silver screws for which you have to use J0 head bits, and 1 small black screw for which you have to use a J000 head bit.

After removing the outer phone case, you will need two Phillips head bits. One J0 and one J000 size.

There are 11 silver screws for which you have to use J0 head bits, and 1 small black screw for which you have to use a J000 head bit.

Step 3

There is a clip on the upper left side of the upper panel. Use the plastic opening tool to pry the clip off of the phone.
The upper inside panel flips up easily off of the phone case once all the clips and screws are removed. If the panel does not pull off easily, check that you have removed all of the screws.
There are ribbons that need to be removed as well. Be sure to carefully pry them off of the board

There is a clip on the upper left side of the upper panel. Use the plastic opening tool to pry the clip off of the phone.

The upper inside panel flips up easily off of the phone case once all the clips and screws are removed. If the panel does not pull off easily, check that you have removed all of the screws.

There are ribbons that need to be removed as well. Be sure to carefully pry them off of the board

Step 4

The bottom inside panel should pry back easily after you take out the screws. Again, if the panel does not pull off easily, you may have missed a screw.

The bottom inside panel should pry back easily after you take out the screws. Again, if the panel does not pull off easily, you may have missed a screw.

Step 5

There are several clips and circuits that need to be released. They are circled in the images above. Be careful not to break any of the attached ribbon or wires. (circle ribbons etc.)
Be careful to use your tools to disconnect the cables at the connectors and not along the wire.

There are several clips and circuits that need to be released. They are circled in the images above. Be careful not to break any of the attached ribbon or wires. (circle ribbons etc.)

Be careful to use your tools to disconnect the cables at the connectors and not along the wire.

Step 6

There are several clips and circuits that need to be released. They are circled in the images above. Be careful not to break any of the attached ribbon or wires.
The orange materials is meant to bend along the dotted line labeled “bend.” Try to make the bend as close to this line as possible.

There are several clips and circuits that need to be released. They are circled in the images above. Be careful not to break any of the attached ribbon or wires.

The orange materials is meant to bend along the dotted line labeled “bend.” Try to make the bend as close to this line as possible.

Step 7

After you have disconnected all of the ribbon and antennae connections, you can remove the board. Gently pry the board up from the bottom of the case and slide it back out.
Make sure to remove all ribbon connectors from the board prior to removing the board.

After you have disconnected all of the ribbon and antennae connections, you can remove the board. Gently pry the board up from the bottom of the case and slide it back out.

Make sure to remove all ribbon connectors from the board prior to removing the board.

Step 8

              Rear Camera

The rear facing camera is attached to the phone case with adhesive. Make sure to use your plastic prying tool to softly remove the camera from the case.
Only use a plastic or ESD safe tool when removing components such as the camera.

The rear facing camera is attached to the phone case with adhesive. Make sure to use your plastic prying tool to softly remove the camera from the case.

Only use a plastic or ESD safe tool when removing components such as the camera.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 4 other contributors

                    Matthew Kowalczyk

Member since: 10/06/2016

322 Reputation

                                      1 Guide authored                  



                       Badges:
                       12







                                                        +9 more badges

Team

                       USF Tampa, Team 5-2, Lacy Fall 2016                        

                                                  Member of USF Tampa, Team 5-2, Lacy Fall 2016 



                    USFT-LACY-F16S5G2                     


                                            4 Members                     


                                            10 Guides authored

Incorrect Tools#

Introduction#

What you need#

Team#

Incorrect Tools

Introduction

What you need

Team