Difficulty
Moderate
Steps
7
Time Required
10 - 15 minutes
Sections
4
- Wristband
- 2 steps
- Rear Case
- 2 steps
- Gasket
- 1 step
- Motherboard
- 2 steps
Flags
0
BackLG G Watch
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Wristband
- Spring bars attach the two halves of the wristband to the watch body. The spring bar has a shoulder on either end.
- Be prepared to apply some pressure with your fingers to perform the following action.
- First, slide the wristband down on the spring bar to expose the shoulder of the spring bar.
- Grasp the exposed shoulder with the tweezers to perform the next step.
Spring bars attach the two halves of the wristband to the watch body. The spring bar has a shoulder on either end.
Be prepared to apply some pressure with your fingers to perform the following action.
First, slide the wristband down on the spring bar to expose the shoulder of the spring bar.
Grasp the exposed shoulder with the tweezers to perform the next step.
1024
Step 2
- This is a challenging step. Do it carefully to prevent the spring bar from flying out of the wristband.
- Use the tweezer to depress the spring bar so that it collapses by a few millimeters and pops out of the hole that was holding it in place.
- Now carefully pull the other end of the spring bar to detach the wristband from the watch face.
- Repeat steps 1 and 2 for the other wristband.
This is a challenging step. Do it carefully to prevent the spring bar from flying out of the wristband.
Use the tweezer to depress the spring bar so that it collapses by a few millimeters and pops out of the hole that was holding it in place.
Now carefully pull the other end of the spring bar to detach the wristband from the watch face.
Repeat steps 1 and 2 for the other wristband.
Step 3
Rear Case
- Use the T5 Torx screwdriver to unscrew the four silver 2mm x 3mm T5 screws that hold the back cover in place.
Use the T5 Torx screwdriver to unscrew the four silver 2mm x 3mm T5 screws that hold the back cover in place.
Step 4
- Slide the opening pick between the rear case and the rest of the device to separate the two halves.
- Gently pull the two halves apart.
Slide the opening pick between the rear case and the rest of the device to separate the two halves.
Gently pull the two halves apart.
Step 5
Gasket
- Use a pair of tweezers to remove the gasket that lies embedded in a groove that runs around the perimeter of the front half.
Use a pair of tweezers to remove the gasket that lies embedded in a groove that runs around the perimeter of the front half.
Step 6
Motherboard
- Use the spudger to gently lift up and disconnect the display connector.
- Now use the spudger to disconnect the digitizer connector.
Use the spudger to gently lift up and disconnect the display connector.
Now use the spudger to disconnect the digitizer connector.
Step 7
- Use a Phillips #000 screwdriver to remove the two black PHO 2.5mm x 3mm screws.
- Use the spudger to gently remove the motherboard.
Use a Phillips #000 screwdriver to remove the two black PHO 2.5mm x 3mm screws.
Use the spudger to gently remove the motherboard.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
4 other people completed this guide.
Author
with 7 other contributors
Meles Anneaud
Member since: 09/23/2014
140 Reputation
1 Guide authored
Badges:
6
+3 more badges
Team
USF Tampa, Team 2-5, Blackwell Fall 2014
Member of USF Tampa, Team 2-5, Blackwell Fall 2014
USFT-BLACKWELL-F14S2G5
5 Members
9 Guides authored
Vassago U7 (VassagoU7) - Nov 4, 2018
Reply
is it possible to replace the battery which is in the board?
