Difficulty
Easy
Steps
8
Time Required
1 - 10 minutes
Sections
3
- Removing the Back Cover
- 2 steps
- Motherboard
- 5 steps
- Front Facing Camera
- 1 step
Flags
0
BackLG G Pad 7.0 LTE
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Removing the Back Cover
- Power off your device before beginning the battery replacement (hold the button with the red marker until the device prompts you to power it off, then tap “Power Off”).
- Be wary of the front screen and SIM Card while tearing down the device.
Power off your device before beginning the battery replacement (hold the button with the red marker until the device prompts you to power it off, then tap “Power Off”).
Be wary of the front screen and SIM Card while tearing down the device.
1024
Step 2
- Put on an Anti-Static Wrist Strap to prevent damage to sensitive electrical components (optional).
- To separate the frame from the cover, pry between the screen and the cover using a plastic prying tool.
- Begin at the top left of the device to avoid damaging the motherboard and work your way around the perimeter of the screen.
- When you pry your device open, be wary of the volume rockers, motherboard, and camera. These components are delicate and can be sensitive to static electricity.
Put on an Anti-Static Wrist Strap to prevent damage to sensitive electrical components (optional).
To separate the frame from the cover, pry between the screen and the cover using a plastic prying tool.
Begin at the top left of the device to avoid damaging the motherboard and work your way around the perimeter of the screen.
When you pry your device open, be wary of the volume rockers, motherboard, and camera. These components are delicate and can be sensitive to static electricity.
Step 3
Motherboard
- Disconnect the battery connector by prying it upwards (red marker).
- Be careful not to damage it while doing so.
- Remove the ribbon cables by prying them upwards with a plastic pry tool ).
- Do not bend the cable or connector as they are fragile.
Disconnect the battery connector by prying it upwards (red marker).
Be careful not to damage it while doing so.
Remove the ribbon cables by prying them upwards with a plastic pry tool ).
Do not bend the cable or connector as they are fragile.
Step 4
- There is a light adhesive holding the camera in the device.
- Using tweezers or a small plastic pry tool gently pull or pry the camera out of the device.
There is a light adhesive holding the camera in the device.
Using tweezers or a small plastic pry tool gently pull or pry the camera out of the device.
Step 5
- Pry the audio jack from the device using a spudger.
Pry the audio jack from the device using a spudger.
Step 6
- Remove the 7 Black 3mm PH0 screws from the motherboard (red markers).
Remove the 7 Black 3mm PH0 screws from the motherboard (red markers).
Step 7
- Remove the Motherboard.
Remove the Motherboard.
Step 8
Front Facing Camera
- Gently pull up on the camera to remove it.
- There is a light adhesive holding the camera in the device
Gently pull up on the camera to remove it.
There is a light adhesive holding the camera in the device
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 3 other contributors
Fadi Bitar
Member since: 09/26/2016
880 Reputation
6 Guides authored
Badges:
12
+9 more badges
Team
USF Tampa, Team 14-6, Eyestone Fall 2016
Member of USF Tampa, Team 14-6, Eyestone Fall 2016
USFT-EYESTONE-F16S14G6
4 Members
12 Guides authored