Difficulty

Moderate

Steps

14

Time Required

                          10 - 30 minutes

Sections

4

  • Battery
  • 2 steps
  • Loudspeaker Assembly
  • 2 steps
  • Touch screen/digitizer
  • 9 steps
  • Charging Port
  • 1 step

Flags

1

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackLG Escape P870

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Battery
  • Turn the device over and pull the back plastic cover off by inserting your fingernail into the opening at the bottom of the phone and gently pulling.

Turn the device over and pull the back plastic cover off by inserting your fingernail into the opening at the bottom of the phone and gently pulling.

1024

Step 2

  • With your finger and from the bottom edge, lift the battery out of the phone and set it aside.
  • You now have access to:
  • Your SD card
  • Your SIM card
  • Your device’s serial numbers

With your finger and from the bottom edge, lift the battery out of the phone and set it aside.

You now have access to:

Your SD card

Your SIM card

Your device’s serial numbers

Step 3

              Loudspeaker Assembly
  • Remove the 4 Phillips 00 screws securing the speaker assembly to the phone housing.

Remove the 4 Phillips 00 screws securing the speaker assembly to the phone housing.

Step 4

  • Carefully insert a small flathead screwdriver between the speaker assembly and the rear housing
  • Pry the speaker assembly out of the phone and set it aside

Carefully insert a small flathead screwdriver between the speaker assembly and the rear housing

Pry the speaker assembly out of the phone and set it aside

Step 5

              Touch screen/digitizer
  • Remove the remaining 6 screws securing the plastic frame to the back housing

Remove the remaining 6 screws securing the plastic frame to the back housing

Step 6

  • Insert a black plastic spudger or a small flathead screwdriver between the back silver bezel and the black area and begin prying the bezel away from the rest of the phone
  • Continue working your way around the phone, prying carefully with your prying tool
  • When you work the frame free, set it aside

Insert a black plastic spudger or a small flathead screwdriver between the back silver bezel and the black area and begin prying the bezel away from the rest of the phone

Continue working your way around the phone, prying carefully with your prying tool

When you work the frame free, set it aside

Step 7

  • Wifi and cell service antennas
  • LCD connector
  • Back camera connector
  • Front camera connector
  • Touch screen/ digitizer connector
  • Charger port connector
  • Headphone jack connector

Wifi and cell service antennas

LCD connector

Back camera connector

Front camera connector

Touch screen/ digitizer connector

Charger port connector

Headphone jack connector

Step 8

  • With a spudger or safe open pry tool, carefully detach the LCD flex connector
  • Release the two antennae from their connectors
  • Release the back camera’s flex from its connector

With a spudger or safe open pry tool, carefully detach the LCD flex connector

Release the two antennae from their connectors

Release the back camera’s flex from its connector

Step 9

  • Release the charging port flex from its connector
  • Release the front camera’s flex from its connector
  • Release the touch screen/digitizer’s flex cable from its connector

Release the charging port flex from its connector

Release the front camera’s flex from its connector

Release the touch screen/digitizer’s flex cable from its connector

Step 10

  • Release the headphone jack’s flex cable from its connector

Release the headphone jack’s flex cable from its connector

Step 11

  • With a pair of tweezers, VERY carefully pull the volume button flex out of the rear housing
  • Repeat the process with the power button flex cable
  • The power button and volume button flex cables will tear very easily, so be cautious

With a pair of tweezers, VERY carefully pull the volume button flex out of the rear housing

Repeat the process with the power button flex cable

The power button and volume button flex cables will tear very easily, so be cautious

Step 12

  • Lift the motherboard away from the housing, taking extra care not to snag any of the antennae or flex cables
  • Set the motherboard aside

Lift the motherboard away from the housing, taking extra care not to snag any of the antennae or flex cables

Set the motherboard aside

Step 13

  • Insert a small flathead screwdriver or black plastic spudger between the front silver bezel and the black plastic mid-frame
  • Gently pry on the bezel to release the clips adhering the screen to the mid-frame
  • Work your way around the phone, still using the small flathead or spudger, until the screen is fully separated
  • Remove the screen, taking care not to tear the flex cable that is still threaded through the housing.
  • After carefully threading the digitizer and outer housing/bezel from the middle bracket you’ll notice the digitizer is held on by a band of very strong adhesive - this will be destroyed when you take off the old digitizer. When you replace your digitizer you can use double-sided tape or epoxy to hold the new digitizer on the bezel.

Insert a small flathead screwdriver or black plastic spudger between the front silver bezel and the black plastic mid-frame

Gently pry on the bezel to release the clips adhering the screen to the mid-frame

Work your way around the phone, still using the small flathead or spudger, until the screen is fully separated

Remove the screen, taking care not to tear the flex cable that is still threaded through the housing.

After carefully threading the digitizer and outer housing/bezel from the middle bracket you’ll notice the digitizer is held on by a band of very strong adhesive - this will be destroyed when you take off the old digitizer. When you replace your digitizer you can use double-sided tape or epoxy to hold the new digitizer on the bezel.

Step 14

              Charging Port
  • Gently pry the charging port assembly’s ribbon cable starting at the top (marked in blue)
  • Slowly peel the ribbon cable downward until the charging port assembly is no longer adhered to the housing
  • Remove the assembly and set it aside
  • Be careful not to tear the antennae when pulling the charging assembly out of the phone

Gently pry the charging port assembly’s ribbon cable starting at the top (marked in blue)

Slowly peel the ribbon cable downward until the charging port assembly is no longer adhered to the housing

Remove the assembly and set it aside

Be careful not to tear the antennae when pulling the charging assembly out of the phone

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 1 other contributor 


                    Brad

Member since: 08/12/2012

1,830 Reputation

                                      10 Guides authored                  



                       Badges:
                       21







                                                        +18 more badges

eli cohen - Jun 2, 2017

Reply

Hi

I didn’t understand why do you need to do part 13?