Difficulty
Moderate
Steps
19
Time Required
30 - 45 minutes
Sections
5
- Battery
- 2 steps
- Rear Case
- 2 steps
- Motherboard
- 5 steps
- Option Buttons
- 8 steps
- Front Keyboard
- 2 steps
Flags
3
Inconsistent Images
Updating the images on this guide to be more consistent with the prerequisites would increase its awesomeness.
Incorrect Tools
Help make this guide better by using the correct tools in images and/or text.
Better Introduction
Improve this guide by completing or revising its introduction.
BackLG Cosmos 2
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Battery
- Insert the plastic opener into the slot at the top of the device.
- Apply gentle pressure with the plastic tool to pop the back case off.
Insert the plastic opener into the slot at the top of the device.
Apply gentle pressure with the plastic tool to pop the back case off.
1024
Step 2
- Use the plastic opener to lift, and remove, the device battery.
Use the plastic opener to lift, and remove, the device battery.
Step 3
Rear Case
- Use a screwdriver and corresponding bit to remove the six 2mm screws that are located along the edge of the rear case. Set the screws aside.
Use a screwdriver and corresponding bit to remove the six 2mm screws that are located along the edge of the rear case. Set the screws aside.
Step 4
- Use the plastic opener to pry the rear case loose.
- This can be difficult. You will need to pry around the entire edge of the rear case, not just in one place.
Use the plastic opener to pry the rear case loose.
This can be difficult. You will need to pry around the entire edge of the rear case, not just in one place.
Step 5
Motherboard
- Use a screwdriver and corresponding bit to remove the two 3mm screws that attach the motherboard to the front case. Set the screws aside
Use a screwdriver and corresponding bit to remove the two 3mm screws that attach the motherboard to the front case. Set the screws aside
Step 6
- Rotate the phone 180 degrees and use the plastic opener to lift the metal piece that covers the ribbon cable.
Rotate the phone 180 degrees and use the plastic opener to lift the metal piece that covers the ribbon cable.
Step 7
- Use the plastic opener to disconnect the ribbon cable.
Use the plastic opener to disconnect the ribbon cable.
Step 8
- Use tweezers to disconnect the two cables that attach the motherboard to the case.
- Note: Pull on the cables gently to prevent damage for future use.
Use tweezers to disconnect the two cables that attach the motherboard to the case.
Note: Pull on the cables gently to prevent damage for future use.
Step 9
- Remove the motherboard from the front case.
Remove the motherboard from the front case.
Step 10
Option Buttons
- Use a screwdriver and corresponding bit to remove the four 1mm screws. Set the screws aside.
Use a screwdriver and corresponding bit to remove the four 1mm screws. Set the screws aside.
Step 11
- Pull the ribbon cable through the slit in the keyboard case to separate it from the sliding mechanism.
Pull the ribbon cable through the slit in the keyboard case to separate it from the sliding mechanism.
Step 12
- Use a screwdriver and corresponding bit to remove the four 3mm screws. Set the screws aside.
- Note: Two of the screws may be hidden underneath a black rubber film. Pull off this film if necessary.
Use a screwdriver and corresponding bit to remove the four 3mm screws. Set the screws aside.
Note: Two of the screws may be hidden underneath a black rubber film. Pull off this film if necessary.
Step 13
- Use the plastic opener to pry open the front of the phone.
- Slip the ribbon cable through the slit to fully separate the two pieces.
Use the plastic opener to pry open the front of the phone.
Slip the ribbon cable through the slit to fully separate the two pieces.
Step 14
- Use a screwdriver and corresponding bit to remove the two 1mm screws. Set the screws aside.
Use a screwdriver and corresponding bit to remove the two 1mm screws. Set the screws aside.
Step 15
- Detach the ribbon cable with the plastic opener.
Detach the ribbon cable with the plastic opener.
Step 16
- Use the spudger to pry the metal piece loose.
- Remove the metal piece along with the two ribbon cables.
Use the spudger to pry the metal piece loose.
Remove the metal piece along with the two ribbon cables.
Step 17
- Flip the front of the phone over and the old option buttons will fall out.
- Insert new option buttons.
Flip the front of the phone over and the old option buttons will fall out.
Insert new option buttons.
Step 18
Front Keyboard
- Use a tool to pry open the LCD display. Remove the display and the motherboard-looking device that it’s connected to.
Use a tool to pry open the LCD display. Remove the display and the motherboard-looking device that it’s connected to.
Step 19
- Rotate and remove the keypad from the front case.
Rotate and remove the keypad from the front case.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 4 other contributors
Nick White
Member since: 10/18/2013
851 Reputation
8 Guides authored
Badges:
9
+6 more badges
Team
Clemson, Team 13-1, Benson Fall 2013
Member of Clemson, Team 13-1, Benson Fall 2013
CLEM-BENSON-F13S13G1
3 Members
16 Guides authored