Difficulty
Moderate
Steps
9
Time Required
30 minutes
Sections
5
- Bottom Plate
- 2 steps
- Motherboard
- 3 steps
- Speaker
- 1 step
- Battery
- 2 steps
- Wi-Fi and Bluetooth Card
- 1 step
Flags
0
BackLG CineBeam
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
Bluetooth allows you to wirelessly connect your projector to another device such as a speaker.
Before replacing the Bluetooth card, make sure it is broken by connecting it to multiple devices and seeing if any of them work. If none of your devices are able to connect to the projector but are able to connect to another device, then your Bluetooth card is likely broken.
You will have to remove the motherboard to access the Bluetooth card. While removing it, make sure to use caution while replacing the ribbon cables as they could rip.
Before beginning, make sure to power off the projector completely and disconnect from any external power source.
What you need
Step 1
Bottom Plate
- Remove three 6 mm screws on the bottom plate with a Phillips #00 screwdriver.
Remove three 6 mm screws on the bottom plate with a Phillips #00 screwdriver.
1024
Step 2
- Using an iFixit opening tool, pry the bottom plate off of the device and remove it fully.
Using an iFixit opening tool, pry the bottom plate off of the device and remove it fully.
Step 3
Motherboard
- Using an iFixit opening tool, press down the lever on the top of the minilock connector for the speaker and pull the plug out gently.
- Repeat this process to remove the WiFi/Bluetooth card connector.
- Remove the battery connector.
- Remove the fan connectors.
Using an iFixit opening tool, press down the lever on the top of the minilock connector for the speaker and pull the plug out gently.
Repeat this process to remove the WiFi/Bluetooth card connector.
Remove the battery connector.
Remove the fan connectors.
Step 4
- Using an iFixit opening tool, pry up the black plastic tabs on the back of the power button/joystick board cable.
- Gently pull the ribbon cable out of the socket.
- Repeat this process for the two display cables.
Using an iFixit opening tool, pry up the black plastic tabs on the back of the power button/joystick board cable.
Gently pull the ribbon cable out of the socket.
Repeat this process for the two display cables.
Step 5
- Lift the motherboard out of the casing.
Lift the motherboard out of the casing.
Step 6
Speaker
- Use your fingers to lift the speaker from the casing.
Use your fingers to lift the speaker from the casing.
Step 7
Battery
- Turn the device over so the power button is facing up.
- Using an iFixit opening tool, pry open the top of the plastic casing and remove it completely.
Turn the device over so the power button is facing up.
Using an iFixit opening tool, pry open the top of the plastic casing and remove it completely.
Step 8
- Using an iFixit opening tool, remove the battery.
Using an iFixit opening tool, remove the battery.
Step 9
Wi-Fi and Bluetooth Card
- Using an iFixit opening tool, move the plastic clip on the right side of the board out of the way.
- Using an iFixit opening tool, pry the Wi-Fi and Bluetooth card out of its socket.
Using an iFixit opening tool, move the plastic clip on the right side of the board out of the way.
Using an iFixit opening tool, pry the Wi-Fi and Bluetooth card out of its socket.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
John Dalton
Member since: 03/23/2022
384 Reputation
4 Guides authored
Badges:
7
+4 more badges
Team
UMass Dartmouth, Team 1-5, Botvin Spring 2022
Member of UMass Dartmouth, Team 1-5, Botvin Spring 2022
UMASSD-BOTVIN-S22S1G5
3 Members
6 Guides authored
