Difficulty

Moderate

Steps

14

Time Required

                          5 minutes

Sections

5

  • Battery
  • 1 step
  • Back Cover
  • 2 steps
  • Sliding Front
  • 4 steps
  • LCD Board
  • 5 steps
  • Touch Buttons
  • 2 steps

Flags

3

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Bullets!

Better coordination with markups and the color/type of bullets will help make this guide more clear!

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackLG Chocolate

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Battery
  • Find a sliding button on the lower back side of the device and with your finger, slide it to the left firmly.
  • The battery should pop out fairly easily. If not, slide the button further or grab and pull it while sliding the button.

Find a sliding button on the lower back side of the device and with your finger, slide it to the left firmly.

The battery should pop out fairly easily. If not, slide the button further or grab and pull it while sliding the button.

1024

Step 2

              Back Cover
  • Unscrew the four Phillips 00 screws on the four corners under the battery to unfasten the back case from the phone.

Unscrew the four Phillips 00 screws on the four corners under the battery to unfasten the back case from the phone.

Step 3

  • Pry the case off using a plastic opening tool.
  • Continue working the plastic opening tool around the sides of the device, unhooking the eight tabs securing the back cover to the rest of the phone as shown in the second photo.
  • The back speaker will be connected to the motherboard, and must be disconnected to remove the case.

Pry the case off using a plastic opening tool.

Continue working the plastic opening tool around the sides of the device, unhooking the eight tabs securing the back cover to the rest of the phone as shown in the second photo.

The back speaker will be connected to the motherboard, and must be disconnected to remove the case.

Step 4

              Sliding Front
  • Unscrew the 4 Phillips 00 screws that connect the two halves of the phone together.

Unscrew the 4 Phillips 00 screws that connect the two halves of the phone together.

Step 5

  • Between the two halves is a ribbon. Use a plastic opening tool to flip up the lock and disconnect it.

Between the two halves is a ribbon. Use a plastic opening tool to flip up the lock and disconnect it.

Step 6

  • Pry off the plastic tabs that cover two screws, as shown in the first picture.
  • Then, remove the 6 Phillips 00 screws from the back of the case, as shown in the second picture.

Pry off the plastic tabs that cover two screws, as shown in the first picture.

Then, remove the 6 Phillips 00 screws from the back of the case, as shown in the second picture.

Step 7

  • Pry off the back cover from the front of the case using a plastic opening tool.

Pry off the back cover from the front of the case using a plastic opening tool.

Step 8

              LCD Board
  • Pry the front speaker and wireless receiver out of the front case using a spudger.
  • They may be taped into the case, so don’t be afraid to pry hard.

Pry the front speaker and wireless receiver out of the front case using a spudger.

They may be taped into the case, so don’t be afraid to pry hard.

Step 9

  • Starting with the side that has the speaker and receiver, carefully lift the LCD Board out of the case.

Starting with the side that has the speaker and receiver, carefully lift the LCD Board out of the case.

Step 10

  • Unhook the ribbon cable using that flat side of a spudger.

Unhook the ribbon cable using that flat side of a spudger.

Step 11

  • Next, carefully remove the tape from the LCD board.

Next, carefully remove the tape from the LCD board.

Step 12

  • Finally, flip up the black switch to unhook the LCD screen from the LCD board using a spudger.
  • The LCD Board in now accessible.

Finally, flip up the black switch to unhook the LCD screen from the LCD board using a spudger.

The LCD Board in now accessible.

Step 13

              Touch Buttons
  • Using a flat head screwdriver, pry the plastic covering off of the back of the keypad

Using a flat head screwdriver, pry the plastic covering off of the back of the keypad

Step 14

  • Push the keypad from behind to disconnect it from the case.

Push the keypad from behind to disconnect it from the case.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 4 other contributors 


                    Thomas

Member since: 01/18/2013

91 Reputation

                                      4 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       Cal Poly, Team 19-46, Regan Winter 2013                        

                                                  Member of Cal Poly, Team 19-46, Regan Winter 2013 



                    CPSU-REGAN-W13S19G46                     


                                            4 Members                     


                                            22 Guides authored