Difficulty

Moderate

Steps

14

Time Required

                          15 - 25 minutes

Sections

4

  • Battery
  • 2 steps
  • Back Cover
  • 4 steps
  • Motherboard
  • 3 steps
  • Front Case
  • 5 steps

Flags

0

  • BackLG CF360

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • On the back of the phone, place your thumb on the three raised bumps and slide the back cover upward.

On the back of the phone, place your thumb on the three raised bumps and slide the back cover upward.

1024

Step 2

  • Lift and remove the battery.

Lift and remove the battery.

Step 3

              Back Cover
  • Remove the two screw covers at the top of phone with tweezers.

Remove the two screw covers at the top of phone with tweezers.

Step 4

  • Remove the six Phillips #000 (3mm) screws.

Remove the six Phillips #000 (3mm) screws.

Step 5

  • Use the plastic opening tool to pry the back cover off. Insert the tool between the back cover and red mid section and go around the entire phone.
  • The plastic side buttons fall out when you take the back cover off.
  • The back cover is connected to the speaker by red and black wires.

Use the plastic opening tool to pry the back cover off. Insert the tool between the back cover and red mid section and go around the entire phone.

The plastic side buttons fall out when you take the back cover off.

The back cover is connected to the speaker by red and black wires.

Step 6

  • Use the tweezers to remove the red and black wires connecting the speaker to the green motherboard by pinching the sides of the plastic base near the motherboard.
  • Set the back cover with the speaker aside.

Use the tweezers to remove the red and black wires connecting the speaker to the green motherboard by pinching the sides of the plastic base near the motherboard.

Set the back cover with the speaker aside.

Step 7

              Motherboard
  • Use the plastic opening tool to gently lift the snapped-in motherboard from the front panel.
  • An orange ribbon from the LCD is connected to the underside of the motherboard, so do not force the motherboard from the rest of the phone yet.

Use the plastic opening tool to gently lift the snapped-in motherboard from the front panel.

An orange ribbon from the LCD is connected to the underside of the motherboard, so do not force the motherboard from the rest of the phone yet.

Step 8

  • Gently remove the blue transparent tape from the connector.

Gently remove the blue transparent tape from the connector.

Step 9

  • With the plastic opening tool, gently pry the LCD connector from the motherboard.
  • Set the motherboard aside.

With the plastic opening tool, gently pry the LCD connector from the motherboard.

Set the motherboard aside.

Step 10

              Front Case
  • Take the front case and unscrew the four Phillips #000 (1mm) screws around the ribbon.

Take the front case and unscrew the four Phillips #000 (1mm) screws around the ribbon.

Step 11

  • Gently pull the orange ribbon from the number pad casing.
  • Set the number pad case to the side once it is detached from the ribbon.

Gently pull the orange ribbon from the number pad casing.

Set the number pad case to the side once it is detached from the ribbon.

Step 12

  • Remove the two red sticker screw coverings at the top corners with tweezers.

Remove the two red sticker screw coverings at the top corners with tweezers.

Step 13

  • Unscrew the four Phillips #000 (3mm) screws at the corners of the phone.

Unscrew the four Phillips #000 (3mm) screws at the corners of the phone.

Step 14

  • Pry the red sliding backing from the front cover by inserting the plastic opening tool in between the two sections and going around the entire phone.
  • Set the red sliding backing and front cover to the side.

Pry the red sliding backing from the front cover by inserting the plastic opening tool in between the two sections and going around the entire phone.

Set the red sliding backing and front cover to the side.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 4 other contributors 


                    Kathrine Muirhead

Member since: 10/15/2013

347 Reputation

                                      3 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Cal Poly, Team 4-27, Amido Fall 2013                        

                                                  Member of Cal Poly, Team 4-27, Amido Fall 2013 



                    CPSU-AMIDO-F13S4G27                     


                                            4 Members                     


                                            16 Guides authored