Difficulty

Moderate

Steps

6

Time Required

                          1 hour

Sections

1

  • Fuser Maintenance Kit, 110-120V
  • 6 steps

Flags

2

In Progress

This guide is a work in progress. Reload periodically to see the latest changes!

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackLexmark MX611de

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Right Cover Removal
  • Remove the paper tray
  • Remove the screw securing the right cover to the front of the printer frame.
  • Open the memory access cover that is attached to the right cover
  • Remove the two screws securing the right cover to the RIP shield.
  • Slightly lift the printer, slide the right cover forward, and pull it out and away from the printer

Remove the paper tray

Remove the screw securing the right cover to the front of the printer frame.

Open the memory access cover that is attached to the right cover

Remove the two screws securing the right cover to the RIP shield.

Slightly lift the printer, slide the right cover forward, and pull it out and away from the printer

1024

Step 2

              Left Cover Removal
  • Remove the screw securing the left cover to the front of the printer frame.
  • Release the Two tabs on the bottom of the cover.
  • Pull the cover forward, and remove it from the printer.

Remove the screw securing the left cover to the front of the printer frame.

Release the Two tabs on the bottom of the cover.

Pull the cover forward, and remove it from the printer.

Step 3

              Rear Exit and Cover Removal
  • Open rear door.
  • Pull the exit door upward to release the hinges, and remove.
  • Remove the two screws securing the rear cover.
  • Remove the cover.

Open rear door.

Pull the exit door upward to release the hinges, and remove.

Remove the two screws securing the rear cover.

Remove the cover.

Step 4

              Mounting Brackets Removal
  • Remove the three screws from the Left Mounting Bracket
  • Two different ways to the next step, dependent on experience and/or confidence.
  • Move the the Mounting Bracket over while extending the Stapler Cable out of the way, The Stapler cable does not have to disconnected.
  • Remove the Stapler Cable and Mounting bracket from the printer frame while feeding the cable through the redrive unit and printer frame.
  • Using a pair of pliers, squeeze the nylon mounts to dislodge the stapler connector, and remove the cable.
  • Remove the three screws from the Right mounting bracket.

Remove the three screws from the Left Mounting Bracket

Two different ways to the next step, dependent on experience and/or confidence.

Move the the Mounting Bracket over while extending the Stapler Cable out of the way, The Stapler cable does not have to disconnected.

Remove the Stapler Cable and Mounting bracket from the printer frame while feeding the cable through the redrive unit and printer frame.

Using a pair of pliers, squeeze the nylon mounts to dislodge the stapler connector, and remove the cable.

Remove the three screws from the Right mounting bracket.

Step 5

              Redrive Assembly Removal
  • Remove the Two screws, and then disconnect the reverse solenoid.
  • Do not disconnect the reverse solenoid cable from the controller board.
  • Remove the Six screws securing the redrive assembly.

Remove the Two screws, and then disconnect the reverse solenoid.

Do not disconnect the reverse solenoid cable from the controller board.

Remove the Six screws securing the redrive assembly.

Step 6

              Fuser Removal
  • Disconnect the cable JEXIT1 from the controller board.
  • Disconnect the Two cables.
  • Remove the Two screws securing the fuser.

Disconnect the cable JEXIT1 from the controller board.

Disconnect the Two cables.

Remove the Two screws securing the fuser.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 


                    alarson118

Member since: 02/24/2015

523 Reputation

                                      3 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       Tech-zone                        

                                                  Member of Tech-zone 



                    Business                     


                                            2 Members                     


                                            3 Guides authored