Lexibook Tablet One Lcd Digitizer Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

Suggest a time??

Sections

Battery
5 steps
MotherBoard
5 steps
LCD / Digitizer
3 steps

Flags

BackLexiBook Tablet One
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

First the case must be opened. Insert the blue plastic opening tool where the two casings meet. Pry up until you hear a clip pop and then carefully move around the device. Do this until the front and back casing are completely separate from one another.
You will again need to be careful opening the device in order to avoid damaging the speaker, or worse, the motherboard.
The clips holding the case together are roughly 1.5 in. apart.

First the case must be opened. Insert the blue plastic opening tool where the two casings meet. Pry up until you hear a clip pop and then carefully move around the device. Do this until the front and back casing are completely separate from one another.

You will again need to be careful opening the device in order to avoid damaging the speaker, or worse, the motherboard.

The clips holding the case together are roughly 1.5 in. apart.

1024

Step 2

Carefully remove the speaker by inserting the spudger between the case and the speaker. Pry upwards until the speaker comes out. Set the speaker to the side.
Be careful with the speaker wires. The wires can easily detach from both the speaker and the board.

Carefully remove the speaker by inserting the spudger between the case and the speaker. Pry upwards until the speaker comes out. Set the speaker to the side.

Be careful with the speaker wires. The wires can easily detach from both the speaker and the board.

Step 3

Use the spudger to repeatedly gouge between the battery and LCD. Work around the battery until it breaks free.
It may feel as though you are pushing extremely hard. This is normal as the adhesive is quite strong. As long as you don’t tip the tool you use and puncture the battery / LCD it will be fine.

Use the spudger to repeatedly gouge between the battery and LCD. Work around the battery until it breaks free.

It may feel as though you are pushing extremely hard. This is normal as the adhesive is quite strong. As long as you don’t tip the tool you use and puncture the battery / LCD it will be fine.

Step 4

The tape around the battery’s circuit board is extremely thorough. There are 2 pieces of tape, on folded over the side and another wrapped around the circuit board. Simply peel both off.

The tape around the battery’s circuit board is extremely thorough. There are 2 pieces of tape, on folded over the side and another wrapped around the circuit board. Simply peel both off.

Step 5

Now that the battery is pry’d free and the tape is removed, the wires should be able to move freely. Give yourself as much room as you need, and solder off the connections on the motherboard.
How to Solder is iFixit’s official guide to use a soldering gun.

Now that the battery is pry’d free and the tape is removed, the wires should be able to move freely. Give yourself as much room as you need, and solder off the connections on the motherboard.

How to Solder is iFixit’s official guide to use a soldering gun.

Step 6

              MotherBoard

Remove the tape from these ribbon cables and their clips.
Wires from the speaker may be under the tape and remain stuck to it, care not to disconnect them from the motherboard.

Remove the tape from these ribbon cables and their clips.

Wires from the speaker may be under the tape and remain stuck to it, care not to disconnect them from the motherboard.

Step 7

Remove the LCD and Digitizer ribbon cables from the motherboard by holding the clips open and pulling the ribbons out.

Remove the LCD and Digitizer ribbon cables from the motherboard by holding the clips open and pulling the ribbons out.

Step 8

Remove the Camera Ribbon Cable, by holding the clip open and pulling the camera out.

Remove the Camera Ribbon Cable, by holding the clip open and pulling the camera out.

Step 9

Using a screwdriver, unscrew the 3 screws which hold the motherboard on the case.
A 3/16 in. Phillips head screw driver will fit the screw heads easily.
These are the only three screws in the device and are all the same size.

Using a screwdriver, unscrew the 3 screws which hold the motherboard on the case.

A 3/16 in. Phillips head screw driver will fit the screw heads easily.

These are the only three screws in the device and are all the same size.

Step 10

You must now use a soldering kit to remove the connections to the motherboard.
The battery wires. (If you had not finished this in an earlier step).
The Speaker Wires.
The Ground.
The LCD wires.
Finally, the microphone, which lies under the board.
How to Solder is iFixit’s official guide to use a soldering gun.

You must now use a soldering kit to remove the connections to the motherboard.

The battery wires. (If you had not finished this in an earlier step).

The Speaker Wires.

The Ground.

The LCD wires.

Finally, the microphone, which lies under the board.

Step 11

              LCD / Digitizer

You will see green grounding tape on the bottom left-hand corner of the LCD. Take a spudger and place it between the casing and the tape. Slowly pry up until you can peel the tape back.
Do not pull the tape all the way off.

You will see green grounding tape on the bottom left-hand corner of the LCD. Take a spudger and place it between the casing and the tape. Slowly pry up until you can peel the tape back.

Do not pull the tape all the way off.

Step 12

Remove the LCD from the clips on one side. Pressing sideways, slide the LCD out.

Remove the LCD from the clips on one side. Pressing sideways, slide the LCD out.

Step 13

In order to remove the digitizer simply push it out of the casing.

In order to remove the digitizer simply push it out of the casing.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 3 other contributors

                    Jordan

Member since: 03/11/2015

630 Reputation

                                      4 Guides authored                  



                       Badges:
                       18







                                                        +15 more badges

Team

                       Colorado Springs, Team 2-5, Panko Spring 2015                        

                                                  Member of Colorado Springs, Team 2-5, Panko Spring 2015 



                    UCCS-PANKO-S15S2G5                     


                                            3 Members                     


                                            10 Guides authored

munozbr - Nov 17, 2016

Où peut on se procurer un autre écran neuf

Introduction#

What you need#

Team#

Introduction

What you need

Team