Difficulty
Moderate
Steps
15
Time Required
20 - 50 minutes
Sections
1
- Lew’s Mach Crush Speed Spool Disassembly
- 15 steps
Flags
2
In Progress
This guide is a work in progress. Reload periodically to see the latest changes!
Member-Contributed Guide
An awesome member of our community made this guide. It is not managed by iFixit staff.
BackLew’s Mach Crush Speed Spool
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Featured Document
Step 1
Lew's Mach Crush Speed Spool Disassembly
- Refer to the featured document for specific part names and exploded view. Determine whether you have the right-handed or left-handed reel.
Refer to the featured document for specific part names and exploded view. Determine whether you have the right-handed or left-handed reel.
1024
Step 2
Remove Left-Side Cover
- Slide switch to ‘open’ on left side of reel to remove left cover.
Slide switch to ‘open’ on left side of reel to remove left cover.
Step 3
Spool Assembly
- Remove the palm-side cover, then spool assembly from center frame of reel.
Remove the palm-side cover, then spool assembly from center frame of reel.
Step 4
Lube-Port Screw
- Remove lube-port screw using small Phillips screwdriver.
Remove lube-port screw using small Phillips screwdriver.
Step 5
Lube-Port Cover
- Remove cover off of lube-port.
Remove cover off of lube-port.
Step 6
Handle Screw
- Remove screw and handle nut from reel.
Remove screw and handle nut from reel.
Step 7
Removal of Handle
- Remove handle and handle nut retainer.
Remove handle and handle nut retainer.
Step 8
Drag-Dial
- Unscrew star-drag until it is loose, remove it and the handle washer from the shaft.
- Note: You may have to hold the reels gears in place in order to unscrew the drag, as it will try to spin the gears.
Unscrew star-drag until it is loose, remove it and the handle washer from the shaft.
Note: You may have to hold the reels gears in place in order to unscrew the drag, as it will try to spin the gears.
Step 9
Exterior Right-Cover Screws
- Remove three spool cover screws from reel.
Remove three spool cover screws from reel.
Step 10
Cap
- Remove cast control cap.
Remove cast control cap.
Step 11
Removal of Right-Cover
- Pry 2 drag spring washers, and 1 click holder washer off to finish removing side cover.
Pry 2 drag spring washers, and 1 click holder washer off to finish removing side cover.
Step 12
Removal of Pinion
- Remove the pinion yoke and 2 pinion yoke springs
Remove the pinion yoke and 2 pinion yoke springs
Step 13
Removal of Main Gear
- Remove drive gear and accompanying drag and ratchet washers.
Remove drive gear and accompanying drag and ratchet washers.
Step 14
Apply Oil
- Apply oil to main gear if desired.
Apply oil to main gear if desired.
Step 15
Make any necessary changes
- At this point, you have disassembled the reel enough to where you can clean parts, remove dust and debris , or replace individual parts
At this point, you have disassembled the reel enough to where you can clean parts, remove dust and debris , or replace individual parts
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Attached Documents
- Reel Manual
- PDF - 14.58 mb
- View
Reel Manual
PDF - 14.58 mb
Author
with 4 other contributors
Rebecca Welch
Member since: 03/31/2022
241 Reputation
1 Guide authored
Badges:
3