Difficulty

Easy

Steps

6

Time Required

                          30 minutes - 1 hour

Sections

2

  • Les Paul Wireless Guitar Body Teardown
  • 3 steps
  • Strummer
  • 3 steps

Flags

0

  • BackGuitar Hero III Guitar

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Les Paul Wireless Guitar Body Teardown
  • Remove batteries

Remove batteries

1024

Step 2

  • Remove void warranty sticker
  • The sticker is covering a torx screw

Remove void warranty sticker

The sticker is covering a torx screw

Step 3

  • Unscrew the 11 screws securing the back of the body using a T10 Torx screwdriver. Each screw is 1 cm long.
  • Push level, this will detach the back of the guitar from the front.
  • Carefully remove the back of the body
  • The battery pack cord is attached to both sides of the guitar, be careful not to tear it apart.
  • The neck connector may be stuck to the back so be sure to detach it before fully pulling

Unscrew the 11 screws securing the back of the body using a T10 Torx screwdriver. Each screw is 1 cm long.

Push level, this will detach the back of the guitar from the front.

Carefully remove the back of the body

The battery pack cord is attached to both sides of the guitar, be careful not to tear it apart.

The neck connector may be stuck to the back so be sure to detach it before fully pulling

Step 4

              Strummer
  • Remove the 4 screws from the back of the strum chip using a Phillips PH1 screwdriver. each of these screws are 1.2 cm each.
  • Remove the 4 inner screws, each are 0.8 cm.
  • Make sure that when putting back together, the 4 inner screws line up with the small plastic piece underneath.

Remove the 4 screws from the back of the strum chip using a Phillips PH1 screwdriver. each of these screws are 1.2 cm each.

Remove the 4 inner screws, each are 0.8 cm.

Make sure that when putting back together, the 4 inner screws line up with the small plastic piece underneath.

Step 5

  • Remove the two plastic holders on the underside of the chip.
  • Pull out the the plastic piece on each side of the strummer.
  • Lift the strummer out of it’s location

Remove the two plastic holders on the underside of the chip.

Pull out the the plastic piece on each side of the strummer.

Lift the strummer out of it’s location

Step 6

  • Take the top black cover off the strummer.
  • Slide the black rod out of the side.
  • Clean if needed.

Take the top black cover off the strummer.

Slide the black rod out of the side.

Clean if needed.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.

Author

                                      with 6 other contributors 


                    Chris

Member since: 10/18/2013

839 Reputation

                                      6 Guides authored                  



                       Badges:
                       14







                                                        +11 more badges

liamiley91 - Apr 30, 2020

Reply

Hi recently bought this controller again and the up strum has stopped functioning. Hoping this will fix it. Thanks

D. Preston Peek - May 27, 2020

Did this fix your issue? Thinking about trying it.

Sébastien Fortuny - Feb 22, 2021

Reply

Same here, i want to it try but want to know if i will be able to do it altough i’m not really good with these kind of work