Les Paul Guitar Pickup Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          25 - 35 minutes

Sections

Pickup
7 steps

Flags

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Better Introduction

Improve this guide by completing or revising its introduction.

BackGuitar
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Pickup

Loosen the guitar strings using a string winder.
The three strings closest unwind clockwise and the three farther away unwind counterclockwise.
Using a coin, carefully begin unscrewing and removing the tailpiece.
You can use a flat head screwdriver, but it will damage the finish on your tailpiece.
Remove the tailpiece by completely unscrewing it from the metal inserts and then gently lifting the assembly out of the body and set off to the side.

Loosen the guitar strings using a string winder.

The three strings closest unwind clockwise and the three farther away unwind counterclockwise.

Using a coin, carefully begin unscrewing and removing the tailpiece.

You can use a flat head screwdriver, but it will damage the finish on your tailpiece.

Remove the tailpiece by completely unscrewing it from the metal inserts and then gently lifting the assembly out of the body and set off to the side.

1024

Step 2

Use the Phillips #0 screwdriver to remove the eight screws keeping the pickups in place.
All screws are the same size.

Use the Phillips #0 screwdriver to remove the eight screws keeping the pickups in place.

All screws are the same size.

Step 3

Note which color wire is coming out of each pickup.
Gently flip over your guitar and put it on a soft towel or other soft material. Take off the control cavity cover.
Desolder the wires of the pickup from the terminal that is touching the back of the potentiometer, or pot.
A potentiometer is what the pickups are wired to that allow the player to have on-board control of their volume and tone. Terminals are the parts on a potentiometer that you solder the wires to.

Note which color wire is coming out of each pickup.

Gently flip over your guitar and put it on a soft towel or other soft material. Take off the control cavity cover.

Desolder the wires of the pickup from the terminal that is touching the back of the potentiometer, or pot.

A potentiometer is what the pickups are wired to that allow the player to have on-board control of their volume and tone. Terminals are the parts on a potentiometer that you solder the wires to.

Step 4

Flip over your guitar again. Thread the wire of the new pickup through the body to the control cavity and screw in the pickup using the Phillips #0 screwdriver.
Check what color wire is coming from each pickup.
For these kinds of pickups, the neck pickup magnet should face the neck and the bridge pickup magnets should face the bridge.

Flip over your guitar again. Thread the wire of the new pickup through the body to the control cavity and screw in the pickup using the Phillips #0 screwdriver.

Check what color wire is coming from each pickup.

For these kinds of pickups, the neck pickup magnet should face the neck and the bridge pickup magnets should face the bridge.

Step 5

Do not touch the soldering iron, or let it touch anything but the solder and wires.
The pickup wire should have multiple wires inside it. Check with the manufacturer which wire is which.
Solder the new ground wires to the back of the volume pots or to the terminal touching the back of the pot.

Do not touch the soldering iron, or let it touch anything but the solder and wires.

The pickup wire should have multiple wires inside it. Check with the manufacturer which wire is which.

Solder the new ground wires to the back of the volume pots or to the terminal touching the back of the pot.

Step 6

Do not touch the metal parts of the soldering iron or the solder after melting it, they will burn you.
Relative to the output jack, the bottom row is for the bridge pickup and the top row is for the neck pickup.
Identify your hot wires and volume pots and solder the hot wire to the center terminal of the wires corresponding pot.

Do not touch the metal parts of the soldering iron or the solder after melting it, they will burn you.

Relative to the output jack, the bottom row is for the bridge pickup and the top row is for the neck pickup.

Identify your hot wires and volume pots and solder the hot wire to the center terminal of the wires corresponding pot.

Step 7

Screw back on the control cavity cover and flip over your guitar.
Reattach the tailpiece and tune your guitar.
Raise and lower the pickups as desired using the two screws on the sides of the pickup rings.

Screw back on the control cavity cover and flip over your guitar.

Reattach the tailpiece and tune your guitar.

Raise and lower the pickups as desired using the two screws on the sides of the pickup rings.

Plug in your beloved guitar and rock out with your fresh pickups

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 1 other contributor

                    Tiaron Starrine

Member since: 02/02/2021

231 Reputation

                                      1 Guide authored                  



                       Badges:
                       5







                                                        +2 more badges

Team

                       Embry-Riddle Aeronautical University, Team S7-G19, Rauch Spring 2021                        

                                                  Member of Embry-Riddle Aeronautical University, Team S7-G19, Rauch Spring 2021 



                    ERAU-RAUCH-S21S7G19                     


                                            1 Member                     


                                            1 Guide authored

Needs Better Images#

Better Introduction#

Introduction#

What you need#

Team#

Needs Better Images

Better Introduction

Introduction

What you need

Team