Difficulty

Easy

Steps

16

Time Required

                          20 minutes

Sections

4

  • Back Cover
  • 3 steps
  • Back Camera
  • 4 steps
  • Camera PCB
  • 5 steps
  • Wi-Fi Module
  • 4 steps

Flags

1

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackLenovo Yoga Tablet 10

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Back Cover
  • Remove the two Phillips #000 screws.
  • These screws are located behind the stand for the device.
  • Our device did not include these screws.

Remove the two Phillips #000 screws.

These screws are located behind the stand for the device.

Our device did not include these screws.

1024

Step 2

  • Use a plastic iFixit opening tool to pry the edges of the back case loose by placing it in between the edge of the cover and the screen.
  • Do not immediately attempt to remove the back of the case without attempting Step three, or you risk snapping the back cover.

Use a plastic iFixit opening tool to pry the edges of the back case loose by placing it in between the edge of the cover and the screen.

Do not immediately attempt to remove the back of the case without attempting Step three, or you risk snapping the back cover.

Step 3

  • Use the spudger to reach into the center of the device and pry off the back case by giving it a light force upwards.

Use the spudger to reach into the center of the device and pry off the back case by giving it a light force upwards.

Step 4

              Back Camera
  • Remove one 5mm screw using the Phillips #00 Screwdriver.

Remove one 5mm screw using the Phillips #00 Screwdriver.

Step 5

  • Use the spudger to disconnect the camera and battery from the printed circuit board by putting the spudger in between the connections and the printed circuit board and pushing the spudger up.

Use the spudger to disconnect the camera and battery from the printed circuit board by putting the spudger in between the connections and the printed circuit board and pushing the spudger up.

Step 6

  • Remove one 5mm screw with the Phillips #00 screwdriver.

Remove one 5mm screw with the Phillips #00 screwdriver.

Step 7

  • Use the nylon tip tweezers to push the camera out from between the power button and the kickstand.

Use the nylon tip tweezers to push the camera out from between the power button and the kickstand.

Step 8

              Camera PCB
  • Remove the four 1 mm screws with a Phillips #00 Screwdriver.

Remove the four 1 mm screws with a Phillips #00 Screwdriver.

Step 9

  • Use a spudger to disconnect the ribbon wire by applying a force upwards.

Use a spudger to disconnect the ribbon wire by applying a force upwards.

Step 10

  • Use tweezers to lift up the foil.
  • The foil may tear.

Use tweezers to lift up the foil.

The foil may tear.

Step 11

  • Use the tweezers to lift the black tape from the corner of the printed circuit board.

Use the tweezers to lift the black tape from the corner of the printed circuit board.

Step 12

  • Flip the board 180 degrees towards you using the tweezers.

Flip the board 180 degrees towards you using the tweezers.

Step 13

              Wi-Fi Module
  • Remove the wire from the PCB by pulling it towards the edge of the headphone jack using tweezers.

Remove the wire from the PCB by pulling it towards the edge of the headphone jack using tweezers.

Step 14

  • Remove the one 5mm screw using a Phillips #00 Screwdriver.

Remove the one 5mm screw using a Phillips #00 Screwdriver.

Step 15

  • Using tweezers remove the tape to disconnect the module by pulling it upward.

Using tweezers remove the tape to disconnect the module by pulling it upward.

Step 16

  • Remove the yellow piece of tape by pulling it upward using tweezers.

Remove the yellow piece of tape by pulling it upward using tweezers.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Rachel Potratz

Member since: 01/24/2019

112 Reputation

                                      1 Guide authored                  



                       Badges:
                       4







                                                        +1 more badge

Team

                       Cal Poly, Team S2-G6, White Winter 2019                        

                                                  Member of Cal Poly, Team S2-G6, White Winter 2019 



                    CPSU-WHITE-W19S2G6                     


                                            4 Members                     


                                            7 Guides authored