Lenovo Yoga Tab 3 8 Camera Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          15 - 20 minutes

Sections

Back Cover
3 steps
Hinge
4 steps
Camera
4 steps

Flags

BackLenovo Yoga Tab 3 8
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Back Cover

Open the kickstand by pressing the release button in the center.
Remove the identification sticker with a pair of tweezers to allow access to the two 2mm screws underneath.

Open the kickstand by pressing the release button in the center.

Remove the identification sticker with a pair of tweezers to allow access to the two 2mm screws underneath.

1024

Step 2

Remove the three 2mm screws under the kickstand with a PH00 screwdriver.
The third 2mm screw to the right may have an S sticker covering it which you can scrape off.

Remove the three 2mm screws under the kickstand with a PH00 screwdriver.

The third 2mm screw to the right may have an S sticker covering it which you can scrape off.

Step 3

Starting along the edge opposite of the hinge, insert a plastic opening tool between the screen and the backing to begin separating the small clips holding the backing on.
Work along the edge and then up the sides, separating the clips with the plastic opening tool.
There is adhesive underneath the slot for the SD card so you will need to slowly apply some force to break the adhesive.
As the back is separated from the device, be careful to not lose the power button. It may come loose and fall out.

Starting along the edge opposite of the hinge, insert a plastic opening tool between the screen and the backing to begin separating the small clips holding the backing on.

Work along the edge and then up the sides, separating the clips with the plastic opening tool.

There is adhesive underneath the slot for the SD card so you will need to slowly apply some force to break the adhesive.

As the back is separated from the device, be careful to not lose the power button. It may come loose and fall out.

Step 4

              Hinge

With the tablet oriented screen side down and hinge opposite of you, locate the black plastic piece on the top right.
Remove the upper 4mm and lower 3mm screws with a PH00 screwdriver.

With the tablet oriented screen side down and hinge opposite of you, locate the black plastic piece on the top right.

Remove the upper 4mm and lower 3mm screws with a PH00 screwdriver.

Step 5

Position the kickstand to an almost closed position. Carefully move the plastic block aside and pry the metal lock out with a metal spudger.
Be careful not to pull off the wires connecting the plastic block.
The lock may be difficult to remove so you may need to apply more pressure to release the lock.

Position the kickstand to an almost closed position. Carefully move the plastic block aside and pry the metal lock out with a metal spudger.

Be careful not to pull off the wires connecting the plastic block.

The lock may be difficult to remove so you may need to apply more pressure to release the lock.

Step 6

At the opposite end of the hinge, locate the silver metal bracket over the wires coming from the end of the hinge. Remove the two 3mm screws with a PH00 screwdriver. Lift the bracket off with your fingers.
Removing the bracket will expose two silver connectors at the ends of the wires coming from the end of the hinge. Use tweezers to carefully lift off the two silver connectors.
Locate the smaller metal wire bracket guiding the wires coming from the end of the hinge. Remove the single black 2mm screw with a PH00 screwdriver. Lift the bracket off with your fingers.

At the opposite end of the hinge, locate the silver metal bracket over the wires coming from the end of the hinge. Remove the two 3mm screws with a PH00 screwdriver. Lift the bracket off with your fingers.

Removing the bracket will expose two silver connectors at the ends of the wires coming from the end of the hinge. Use tweezers to carefully lift off the two silver connectors.

Locate the smaller metal wire bracket guiding the wires coming from the end of the hinge. Remove the single black 2mm screw with a PH00 screwdriver. Lift the bracket off with your fingers.

Step 7

Begin removing the entire hinge assembly by lifting it out, starting at the end where the lock is located. Carefully feed the wires through the hinge mount with your fingers as you pull the hinge assembly free.

Begin removing the entire hinge assembly by lifting it out, starting at the end where the lock is located. Carefully feed the wires through the hinge mount with your fingers as you pull the hinge assembly free.

Step 8

              Camera

Locate the silver camera mounting bracket between the power button and the camera housing. Remove the two 3mm screws on the camera mounting bracket using a PH00 screwdriver.

Locate the silver camera mounting bracket between the power button and the camera housing. Remove the two 3mm screws on the camera mounting bracket using a PH00 screwdriver.

Step 9

The camera housing is held in place by a pin in the center of the grey hinge mount. Push and hold in the pin with the pointy end of a spudger while you lift the camera assembly out.

The camera housing is held in place by a pin in the center of the grey hinge mount. Push and hold in the pin with the pointy end of a spudger while you lift the camera assembly out.

Step 10

Remove the three 5mm screws holding together the camera housing using a PH00 screwdriver.

Remove the three 5mm screws holding together the camera housing using a PH00 screwdriver.

Step 11

Separate the camera from the housing by pulling it apart with your fingers.

Separate the camera from the housing by pulling it apart with your fingers.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors

                    Nicklaus Krems

Member since: 09/25/2017

1,049 Reputation

                                      8 Guides authored                  



                       Badges:
                       16







                                                        +13 more badges

Team

                       USF Tampa, Team S16-G2, Eyestone Fall 2017                        

                                                  Member of USF Tampa, Team S16-G2, Eyestone Fall 2017 



                    USFT-EYESTONE-F17S16G2                     


                                            4 Members                     


                                            16 Guides authored

Ste - Apr 7, 2018

These are the best instructions to be found anywhere particularly the close up photographs are very helpful,Thank you.

Introduction#

What you need#

Team#

Introduction

What you need

Team