Difficulty
Moderate
Steps
5
Time Required
30 minutes
Sections
2
- Back Cover
- 3 steps
- Motherboard
- 2 steps
Flags
0
BackLenovo Yoga Tab 3 10
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Back Cover
- Open the built-in kickstand.
Open the built-in kickstand.
1024
Step 2
- Remove the sticker located directly under the the built-in kickstand to reveal two 0.75 mm screws.
- Remove the microSD card slot cover. Remove any microSD card (if inserted).
- Using a Phillips head screwdriver, remove the three 0.75 mm screws.
Remove the sticker located directly under the the built-in kickstand to reveal two 0.75 mm screws.
Remove the microSD card slot cover. Remove any microSD card (if inserted).
Using a Phillips head screwdriver, remove the three 0.75 mm screws.
Step 3
- Orient the device so the screen is facing you.
- Carefully insert the spudger along the seam between the screen and back cover and gently separate the back cover from the device frame.
- Continue to detach the backplate from the frame by moving the spudger around the perimeter.
- Some force will be required to detach the small plastic braces securing the backplate to the device.
Orient the device so the screen is facing you.
Carefully insert the spudger along the seam between the screen and back cover and gently separate the back cover from the device frame.
Continue to detach the backplate from the frame by moving the spudger around the perimeter.
Some force will be required to detach the small plastic braces securing the backplate to the device.
Step 4
Motherboard
- Locate the screws in the motherboard the wire cover assembly and the speakers.
- Use the J000 screwdriver to remove the screws on the motherboard, the wire cover, and the two speakers.
- Disconnect the wifi connector on the motherboard.
Locate the screws in the motherboard the wire cover assembly and the speakers.
Use the J000 screwdriver to remove the screws on the motherboard, the wire cover, and the two speakers.
Disconnect the wifi connector on the motherboard.
Step 5
- Use the spudger to lift the two speakers up from the small adhesive strip.
- Place the spudger in the upper left corner of the motherboard and lift it to separate it from the adhesive strip under it.
- Lift away the motherboard.
Use the spudger to lift the two speakers up from the small adhesive strip.
Place the spudger in the upper left corner of the motherboard and lift it to separate it from the adhesive strip under it.
Lift away the motherboard.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
12 other people completed this guide.
Author
with 4 other contributors
Phanudej
Member since: 02/20/2017
1,166 Reputation
5 Guides authored
Badges:
12
+9 more badges
Team
USF Tampa, Team S3-G2, Sullivan Spring 2017
Member of USF Tampa, Team S3-G2, Sullivan Spring 2017
USFT-SULLIVAN-S17S3G2
4 Members
18 Guides authored
Jozsef Szlatki - Nov 25, 2018
Reply
Dear @phanudej ,
I liked your post. I’d have a remark and a question. I made a mistake during the maintanance; with wich I killed a part of the MOBO. So dear users my advice if you want to connect the LCD connector remove the battery before… I had never this issue but now happened. (the device was switched off)
Could you please take a photo of the powerstage of the LCD (I think it should be that) So between the inductor (100; 10uH coil) and an capacity there is a component I do not know what is it (it smoked away) I assume it is a diode…?! They are in the white rectangle near the LCD connector
Thanks in advance
Best regards
@harrincourt
