Lenovo Yoga C930 13Ikb Power Button Board Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 minutes

Sections

Back Cover
3 steps
Battery
3 steps
SSD
2 steps
Power Button Board
5 steps

Flags

Better Introduction

Improve this guide by completing or revising its introduction.

BackLenovo Yoga C930-13IKB
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Back Cover

Flip the device over so that the underside is facing up.
Remove the six 3.5 mm T5 Torx screws.

Flip the device over so that the underside is facing up.

Remove the six 3.5 mm T5 Torx screws.

1024

Step 2

Pry off the back cover using the plastic opening tool.
Loosen the back cover in multiple spots using the opening tool, then remove the whole back.
You may have to run the plastic tool along the edges until you find a small gap to separate the back cover from the laptop.
Do not use a metal tool when working with your device.

Pry off the back cover using the plastic opening tool.

Loosen the back cover in multiple spots using the opening tool, then remove the whole back.

You may have to run the plastic tool along the edges until you find a small gap to separate the back cover from the laptop.

Do not use a metal tool when working with your device.

Step 3

Carefully lift the cover off with your hands.

Carefully lift the cover off with your hands.

Step 4

              Battery

Unplug the battery from the motherboard by pinching the cables with your fingers and tugging out with force.
Use the spudger for assistance.

Unplug the battery from the motherboard by pinching the cables with your fingers and tugging out with force.

Use the spudger for assistance.

Step 5

Unscrew the four 3mm screws with a Phillips screwdriver.

Unscrew the four 3mm screws with a Phillips screwdriver.

Step 6

The battery is still held in place with two stretch-release adhesive strips, similar to ones found in an iPhone.
Use your fingers to pry up the clear plastic pull-tab for one of the stretch release adhesives.
Grasp the pull-tab and slowly pull away from the battery at a shallow angle. The adhesive strip will stretch to many times its length and slowly release from underneath the battery.
Repeat the procedure for the second strip on the opposite side of the battery.
Be careful not to bend the battery. Breaking the battery is dangerous.
Remove the battery with your hands.

The battery is still held in place with two stretch-release adhesive strips, similar to ones found in an iPhone.

Use your fingers to pry up the clear plastic pull-tab for one of the stretch release adhesives.

Grasp the pull-tab and slowly pull away from the battery at a shallow angle. The adhesive strip will stretch to many times its length and slowly release from underneath the battery.

Repeat the procedure for the second strip on the opposite side of the battery.

Be careful not to bend the battery. Breaking the battery is dangerous.

Remove the battery with your hands.

Step 7

SSD

Remove the screw ( 2 mm with a 5 mm head) that connect the SSD to the motherboard using a Phillips #00 screwdriver.

Remove the screw ( 2 mm with a 5 mm head) that connect the SSD to the motherboard using a Phillips #00 screwdriver.

Step 8

Pinch the left side of the SSD card.
Pull gently to the left, horizontal to the laptop.

Pinch the left side of the SSD card.

Pull gently to the left, horizontal to the laptop.

Step 9

              Power Button Board

Unscrew the two 2mm screws using a Phillips #00 screwdriver.
Gently lift out the digital pen spring using the iFixit opening tool.

Unscrew the two 2mm screws using a Phillips #00 screwdriver.

Gently lift out the digital pen spring using the iFixit opening tool.

Step 10

Remove four 2 mm screws from the digital pen holder using a Phillips #00 screwdriver.
Do not remove the pen holder until the attached ribbon cable is uninstalled.

Remove four 2 mm screws from the digital pen holder using a Phillips #00 screwdriver.

Do not remove the pen holder until the attached ribbon cable is uninstalled.

Step 11

Using the angled ESD tweezers, gently lift the black tab on top of the ZIF connector on the motherboard which connects the power button ribbon cable.
Gently pull the cable out from the connector.

Using the angled ESD tweezers, gently lift the black tab on top of the ZIF connector on the motherboard which connects the power button ribbon cable.

Gently pull the cable out from the connector.

Step 12

Carefully lift out the digital pen holder with the attached power button ribbon cable.

Carefully lift out the digital pen holder with the attached power button ribbon cable.

Step 13

Depress the power button, then gently pull and detach it using the angled ESD tweezers.

Depress the power button, then gently pull and detach it using the angled ESD tweezers.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors

                    Lucas Parton

Member since: 09/20/2021

133 Reputation

                                      1 Guide authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       The Citadel Military College of South Carolina, Team 2-14, Eggleston Fall 2021                        

                                                  Member of The Citadel Military College of South Carolina, Team 2-14, Eggleston Fall 2021 



                    CMCSC-EGGLESTON-F21S2G14                     


                                            3 Members                     


                                            3 Guides authored

Better Introduction#

Introduction#

What you need#

Team#

Better Introduction

Introduction

What you need

Team