Difficulty
Difficult
Steps
13
Time Required
15 - 20 minutes
Sections
3
- Back Cover
- 2 steps
- Motherboard
- 10 steps
- USB - C Port
- 1 step
Flags
0
BackLenovo Yoga 920-13IKB
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Cover
- Flip the device over to access the screws on the back cover.
- Remove the ten 5mm Torx T5 screws on the back cover to loosen the back cover.
Flip the device over to access the screws on the back cover.
Remove the ten 5mm Torx T5 screws on the back cover to loosen the back cover.
1024
Step 2
- Slide the iFixit Opening Tool under the back cover to lift it up.
- Pull up on the cover with your hand to release the tab holding the center of the cover in place.
Slide the iFixit Opening Tool under the back cover to lift it up.
Pull up on the cover with your hand to release the tab holding the center of the cover in place.
Step 3
Motherboard
- Remove the twelve 5mm Phillips #00 screws to loosen the motherboard.
Remove the twelve 5mm Phillips #00 screws to loosen the motherboard.
Step 4
- Flip up the ten flat connectors holding the motherboard using the iFixit Opening Tool to free the motherboard.
Flip up the ten flat connectors holding the motherboard using the iFixit Opening Tool to free the motherboard.
Step 5
- Pull out the ribbon cables from the opened connectors using the iFixit Tweezers to free up the motherboard.
Pull out the ribbon cables from the opened connectors using the iFixit Tweezers to free up the motherboard.
Step 6
- Disconnect the battery by pulling the ribbon wire grouping out of the top of the motherboard.
Disconnect the battery by pulling the ribbon wire grouping out of the top of the motherboard.
Step 7
- Disconnect the red and black wire from the motherboard using the iFixit Tweezers.
Disconnect the red and black wire from the motherboard using the iFixit Tweezers.
Step 8
- Lift the motherboard up parallel to the hinge of the device.
- Gently pull away from the port cutouts of the USB-C and audio jack to remove the motherboard from the device casing.
- Avoid pulling the motherboard all the way out until the green AC card is disconnected.
Lift the motherboard up parallel to the hinge of the device.
Gently pull away from the port cutouts of the USB-C and audio jack to remove the motherboard from the device casing.
Avoid pulling the motherboard all the way out until the green AC card is disconnected.
Step 9
- Disconnect the green AC card plugged into the motherboard by pulling it out with your hands.
Disconnect the green AC card plugged into the motherboard by pulling it out with your hands.
Step 10
- Flip the motherboard over to access the back side.
Flip the motherboard over to access the back side.
Step 11
- Remove four 3mm JIS #00 screws with the screwdriver.
- Remove one 3mm Phillips #00 screw with the screwdriver.
- The screws stay attached to the speaker when removed from the motherboard.
Remove four 3mm JIS #00 screws with the screwdriver.
Remove one 3mm Phillips #00 screw with the screwdriver.
The screws stay attached to the speaker when removed from the motherboard.
Step 12
- Separate the fans from the motherboard to isolate it for replacement.
Separate the fans from the motherboard to isolate it for replacement.
Step 13
USB - C Port
- Replace the motherboard to replace the USB-C ports.
Replace the motherboard to replace the USB-C ports.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 3 other contributors
Alyssa McCulloch
Member since: 01/24/2019
1,721 Reputation
9 Guides authored
Badges:
14
+11 more badges
Team
Cal Poly, Team S2-G3, White Winter 2019
Member of Cal Poly, Team S2-G3, White Winter 2019
CPSU-WHITE-W19S2G3
4 Members
29 Guides authored
