Difficulty

Easy

Steps

9

Time Required

                          10 - 15 minutes

Sections

2

  • Bottom Panel
  • 6 steps
  • Speakers
  • 3 steps

Flags

0

  • BackLenovo Yoga 910-13IKB

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Bottom Panel
  • Before you begin, be sure to turn off your laptop and unplug it from the outlet.
  • Turn the laptop over and remove the ten Torx T5 screws along the perimeter of the bottom panel.
  • Remove the panel.

Before you begin, be sure to turn off your laptop and unplug it from the outlet.

Turn the laptop over and remove the ten Torx T5 screws along the perimeter of the bottom panel.

Remove the panel.

1024

Step 2

  • Remove all 4 screws attached to the battery with a small Phillips head screwdriver.
  • Each screw on the back is M2 x 1.7mm
  • After the screws are taken out, remove the battery.

Remove all 4 screws attached to the battery with a small Phillips head screwdriver.

Each screw on the back is M2 x 1.7mm

After the screws are taken out, remove the battery.

Step 3

  • Remove all 6 screws attached to the trackpad with a small Phillips head screwdriver.
  • Each screw on the back is M2 x 1.7mm
  • Detach the ribbon cable connected to the trackpad using a wedge device.
  • Remove the trackpad using a wedge device

Remove all 6 screws attached to the trackpad with a small Phillips head screwdriver.

Detach the ribbon cable connected to the trackpad using a wedge device.

Remove the trackpad using a wedge device

Step 4

  • Remove all 6 screws attached to the USB ports on both sides of the device with a small Philips head screwdriver.
  • Detach both ribbon cables attached to each USB port with a wedge device, then detach the USB ports.

Remove all 6 screws attached to the USB ports on both sides of the device with a small Philips head screwdriver.

Detach both ribbon cables attached to each USB port with a wedge device, then detach the USB ports.

Step 5

  • Remove all 4 screws attached to SSD stick with a small Phillips head screwdriver.
  • Pull the SSD stick directly to the right until it shifts out of place to remove it.
  • The storage chip above it (further away from you) may also simply be detached by pulling it directly to the right until it clicks out.

Remove all 4 screws attached to SSD stick with a small Phillips head screwdriver.

Pull the SSD stick directly to the right until it shifts out of place to remove it.

The storage chip above it (further away from you) may also simply be detached by pulling it directly to the right until it clicks out.

Step 6

  • Remove all 4 screws attached to both fans, and the back connector strip (long metal piece furthest from you with screws in it) with a small Phillips head screwdriver
  • Remove the back connector strip using a wedge device to pry it off of the device
  • With the back connector strip removed, pry the fans (which are attached) using a wedge device and the fans will now be maintainable.

Remove all 4 screws attached to both fans, and the back connector strip (long metal piece furthest from you with screws in it) with a small Phillips head screwdriver

Remove the back connector strip using a wedge device to pry it off of the device

With the back connector strip removed, pry the fans (which are attached) using a wedge device and the fans will now be maintainable.

Step 7

              Speakers
  • Remove the four silver 3mm JIS #00 screws holding the speakers in place.

Remove the four silver 3mm JIS #00 screws holding the speakers in place.

Step 8

  • Lift up the speaker from the corner of the device.
  • Pull gently on the bundled cable connector at the top of the speaker.
  • Pull evenly on the width of the cable so that no individual wire is overly strained.

Lift up the speaker from the corner of the device.

Pull gently on the bundled cable connector at the top of the speaker.

Pull evenly on the width of the cable so that no individual wire is overly strained.

Step 9

  • Repeat step three for the speaker on the opposite side of the device.

Repeat step three for the speaker on the opposite side of the device.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 3 other contributors 


                    Connor Dilloughery

Member since: 01/23/2020

139 Reputation

                                      1 Guide authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       Cal Poly, Team S1-G5, White Winter 2020                        

                                                  Member of Cal Poly, Team S1-G5, White Winter 2020 



                    CPSU-WHITE-W20S1G5                     


                                            4 Members                     


                                            14 Guides authored