Lenovo Yoga 910 13Ikb Motherboard Replacement Repair Guide

Difficulty

Moderate

Steps

8

Time Required

                          30 - 45 minutes            

Sections

4

• Back Panel
• 1 step
• Battery
• 2 steps
• Trackpad
• 1 step
• Motherboard
• 4 steps

Flags

5

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Needs More Images

A few more images would make this guide’s procedures crystal clear.

Inconsistent Images

Updating the images on this guide to be more consistent with the prerequisites would increase its awesomeness.

Better Introduction

Improve this guide by completing or revising its introduction.

• BackLenovo Yoga 910-13IKB

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Back Panel               

• Turn the laptop over and remove the ten Torx T5 screws along the perimeter of the bottom panel using the T5 Torx Screwdriver.
• Remove the back panel from the device exposing the components.

Turn the laptop over and remove the ten Torx T5 screws along the perimeter of the bottom panel using the T5 Torx Screwdriver.

Remove the back panel from the device exposing the components.

1024

Step 2

              Battery               

• Remove the four 3 mm Phillips #0 screws holding the battery in place.

Remove the four 3 mm Phillips #0 screws holding the battery in place.

Step 3

• Disconnect the battery cable from its motherboard socket by gently pulling it towards the battery. The spudger tool may be needed to lift the flap seal.
• Pull parallel to the battery, not straight up.
• Pull evenly on the width of the cable so that no individual wire is overly strained.
• Lift the battery out.

Disconnect the battery cable from its motherboard socket by gently pulling it towards the battery. The spudger tool may be needed to lift the flap seal.

Pull parallel to the battery, not straight up.

Pull evenly on the width of the cable so that no individual wire is overly strained.

Lift the battery out.

Step 4

              Trackpad               

• Using the Phillips #0 screwdriver, remove all six screws holding the trackpad to the device.
• Find the ribbon cable, the black bundle of wires attached to the trackpad, and lift the head of the ribbon cable towards you.
• Carefully lift up the trackpad and remove it from the device.

Using the Phillips #0 screwdriver, remove all six screws holding the trackpad to the device.

Find the ribbon cable, the black bundle of wires attached to the trackpad, and lift the head of the ribbon cable towards you.

Carefully lift up the trackpad and remove it from the device.

Step 5

              Motherboard               

• Remove the screws attached to the USB ports on both sides of the device with a Phillips #0 screwdriver.
• Detach both of the ribbon cables attached to each USB port with a wedge device, then detach the USB ports.

Remove the screws attached to the USB ports on both sides of the device with a Phillips #0 screwdriver.

Detach both of the ribbon cables attached to each USB port with a wedge device, then detach the USB ports.

Step 6

• Remove the screws attached to the SSD stick with a Phillips #0 screwdriver.
• Pull the SSD stick directly to the right until it shifts out of place to remove it.
• Storage chip above it (further away from you) may also be detached by pulling it directly to the right until it clicks out.

Remove the screws attached to the SSD stick with a Phillips #0 screwdriver.

Pull the SSD stick directly to the right until it shifts out of place to remove it.

Storage chip above it (further away from you) may also be detached by pulling it directly to the right until it clicks out.

Step 7

• Remove the four screws attached to both fans, and the back connector strip (the long metal piece furthest from you with screws in it) with a Phillips #0 screwdriver.

Remove the four screws attached to both fans, and the back connector strip (the long metal piece furthest from you with screws in it) with a Phillips #0 screwdriver.

Step 8

• Remove the screws attached to the motherboard with a Phillips #0 screwdriver.
• Remove the back connector strip using a spudger or plastic opening tool to pry it off of the device.
• With the back connector strip removed, pry the motherboard up and off of the device.

Remove the screws attached to the motherboard with a Phillips #0 screwdriver.

Remove the back connector strip using a spudger or plastic opening tool to pry it off of the device.

With the back connector strip removed, pry the motherboard up and off of the device.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 3 other contributors 

                    Isaiah M Allgeyer                     

Member since: 02/15/2021

217 Reputation

                                      2 Guides authored                  



                       Badges:
                       4







                                                        +1 more badge                           

Team

                       The Citadel Military College of South Carolina, Team S1-G8, Eggleston Spring 2021                        

                                                  Member of The Citadel Military College of South Carolina, Team S1-G8, Eggleston Spring 2021 



                    CMCSC-EGGLESTON-S21S1G8                     


                                            3 Members                     


                                            3 Guides authored