Lenovo Yoga 910 13Ikb Fingerprint Reader Replacement Repair Guide

Difficulty

Easy

Steps

Time Required

                          10 - 15 minutes

Sections

Bottom Panel
6 steps
Battery
2 steps
Fingerprint Reader
4 steps

Flags

BackLenovo Yoga 910-13IKB
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Bottom Panel

Before you begin, be sure to turn off your laptop and unplug it from the outlet.
Turn the laptop over and remove the ten Torx T5 screws along the perimeter of the bottom panel.
Remove the panel.

Before you begin, be sure to turn off your laptop and unplug it from the outlet.

Turn the laptop over and remove the ten Torx T5 screws along the perimeter of the bottom panel.

Remove the panel.

1024

Step 2

Remove all 4 screws attached to the battery with a small Phillips head screwdriver.
Each screw on the back is M2 x 1.7mm
After the screws are taken out, remove the battery.

Remove all 4 screws attached to the battery with a small Phillips head screwdriver.

Each screw on the back is M2 x 1.7mm

After the screws are taken out, remove the battery.

Step 3

Remove all 6 screws attached to the trackpad with a small Phillips head screwdriver.
Each screw on the back is M2 x 1.7mm
Detach the ribbon cable connected to the trackpad using a wedge device.
Remove the trackpad using a wedge device

Remove all 6 screws attached to the trackpad with a small Phillips head screwdriver.

Detach the ribbon cable connected to the trackpad using a wedge device.

Remove the trackpad using a wedge device

Step 4

Remove all 6 screws attached to the USB ports on both sides of the device with a small Philips head screwdriver.
Detach both ribbon cables attached to each USB port with a wedge device, then detach the USB ports.

Remove all 6 screws attached to the USB ports on both sides of the device with a small Philips head screwdriver.

Detach both ribbon cables attached to each USB port with a wedge device, then detach the USB ports.

Step 5

Remove all 4 screws attached to SSD stick with a small Phillips head screwdriver.
Pull the SSD stick directly to the right until it shifts out of place to remove it.
The storage chip above it (further away from you) may also simply be detached by pulling it directly to the right until it clicks out.

Remove all 4 screws attached to SSD stick with a small Phillips head screwdriver.

Pull the SSD stick directly to the right until it shifts out of place to remove it.

The storage chip above it (further away from you) may also simply be detached by pulling it directly to the right until it clicks out.

Step 6

Remove all 4 screws attached to both fans, and the back connector strip (long metal piece furthest from you with screws in it) with a small Phillips head screwdriver
Remove the back connector strip using a wedge device to pry it off of the device
With the back connector strip removed, pry the fans (which are attached) using a wedge device and the fans will now be maintainable.

Remove all 4 screws attached to both fans, and the back connector strip (long metal piece furthest from you with screws in it) with a small Phillips head screwdriver

Remove the back connector strip using a wedge device to pry it off of the device

With the back connector strip removed, pry the fans (which are attached) using a wedge device and the fans will now be maintainable.

Step 7

              Battery

Remove the four 3 mm Phillips #0 screws holding the battery in place.

Remove the four 3 mm Phillips #0 screws holding the battery in place.

Step 8

Disconnect the battery cable from its motherboard socket by gently pulling it towards the battery. The spudger tool may be needed to lift the flap seal.
Pull parallel to the battery, not straight up.
Pull evenly on the width of the cable so that no individual wire is overly strained.
Lift the battery out.

Disconnect the battery cable from its motherboard socket by gently pulling it towards the battery. The spudger tool may be needed to lift the flap seal.

Pull parallel to the battery, not straight up.

Pull evenly on the width of the cable so that no individual wire is overly strained.

Lift the battery out.

Step 9

              Fingerprint Reader

Remove the one 3mm JIS #00 screw on the right side of the silver component.

Remove the one 3mm JIS #00 screw on the right side of the silver component.

Step 10

Gently pull up on the ribbon cable to detach it from the metal housing.

Gently pull up on the ribbon cable to detach it from the metal housing.

Step 11

Lift the metal housing out and set it aside. This component holds the reader in place.
The left side of the component is tucked under the lip of the computer, so lift from the right side of the component.

Lift the metal housing out and set it aside. This component holds the reader in place.

The left side of the component is tucked under the lip of the computer, so lift from the right side of the component.

Step 12

Remove the fingerprint reader from its place.

Remove the fingerprint reader from its place.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 3 other contributors

                    Nikki Sorfleet

Member since: 01/23/2020

151 Reputation

                                      1 Guide authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Cal Poly, Team S1-G5, White Winter 2020                        

                                                  Member of Cal Poly, Team S1-G5, White Winter 2020 



                    CPSU-WHITE-W20S1G5                     


                                            4 Members                     


                                            14 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team