Difficulty
Moderate
Steps
16
Time Required
40 minutes - 1 hour
Sections
3
- Back Panel
- 1 step
- Battery
- 2 steps
- Fan
- 13 steps
Flags
0
BackLenovo Yoga 910-13IKB
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Panel
- Turn the laptop over and remove the ten Torx T5 screws along the perimeter of the bottom panel using the T5 Torx Screwdriver.
- Remove the back panel from the device exposing the components.
Turn the laptop over and remove the ten Torx T5 screws along the perimeter of the bottom panel using the T5 Torx Screwdriver.
Remove the back panel from the device exposing the components.
1024
Step 2
Battery
- Remove the four 3 mm Phillips #0 screws holding the battery in place.
Remove the four 3 mm Phillips #0 screws holding the battery in place.
Step 3
- Disconnect the battery cable from its motherboard socket by gently pulling it towards the battery. The spudger tool may be needed to lift the flap seal.
- Pull parallel to the battery, not straight up.
- Pull evenly on the width of the cable so that no individual wire is overly strained.
- Lift the battery out.
Disconnect the battery cable from its motherboard socket by gently pulling it towards the battery. The spudger tool may be needed to lift the flap seal.
Pull parallel to the battery, not straight up.
Pull evenly on the width of the cable so that no individual wire is overly strained.
Lift the battery out.
Step 4
Fan
- Remove the screws attached to the SSD stick by using a Phillips #0 screwdriver.
- Pull the SSD stick directly to the right until it shifts out of place to remove it.
Remove the screws attached to the SSD stick by using a Phillips #0 screwdriver.
Pull the SSD stick directly to the right until it shifts out of place to remove it.
Step 5
- Lift the labeled flap seal and remove the ribbon cable that connects the USB ports to the motherboard and gently pull away.
- Be gentle when detaching the cables, the attachment port is easy to damage.
Lift the labeled flap seal and remove the ribbon cable that connects the USB ports to the motherboard and gently pull away.
Be gentle when detaching the cables, the attachment port is easy to damage.
Step 6
- Unscrew the single 1 mm screw at the left of Wi-Fi card with a Phillips #0 screwdriver.
- Remove the Wi-Fi card by gently pulling the card to the left.
Unscrew the single 1 mm screw at the left of Wi-Fi card with a Phillips #0 screwdriver.
Remove the Wi-Fi card by gently pulling the card to the left.
Step 7
- Unscrew three 1 mm screws on the rightmost USB port board using a Phillips #0 screwdriver.
- Remove the rightmost USB port board by pulling it up and out.
Unscrew three 1 mm screws on the rightmost USB port board using a Phillips #0 screwdriver.
Remove the rightmost USB port board by pulling it up and out.
Step 8
- Unscrew the four 1 mm screws on the leftmost USB port using a Phillips #0 screwdriver.
- Remove the leftmost USB port board by pulling it up and out.
Unscrew the four 1 mm screws on the leftmost USB port using a Phillips #0 screwdriver.
Remove the leftmost USB port board by pulling it up and out.
Step 9
- Remove seven 1 mm screws from the motherboard using a Phillips #0 screwdriver.
Remove seven 1 mm screws from the motherboard using a Phillips #0 screwdriver.
Step 10
- Gently pull the Back Connector strip towards you, this will safely disconnect it.
- Disconnect the two Upper Connector Strips by using Tweezers and unclipping the upper tab.
- Be cautious not to rip the strips or parts.
Gently pull the Back Connector strip towards you, this will safely disconnect it.
Disconnect the two Upper Connector Strips by using Tweezers and unclipping the upper tab.
Be cautious not to rip the strips or parts.
Step 11
- Gently peel up the sticky adhesive attaching the fan to the hinge.
- Be very careful with the ports when removing to not damage anything else.
Gently peel up the sticky adhesive attaching the fan to the hinge.
Be very careful with the ports when removing to not damage anything else.
Step 12
- Remove the motherboard and fan by pulling away and up from the hinge.
Remove the motherboard and fan by pulling away and up from the hinge.
Step 13
- Flip the component to the opposite side.
Flip the component to the opposite side.
Step 14
- Remove three 1 mm screws using a Phillips #0 screwdriver.
Remove three 1 mm screws using a Phillips #0 screwdriver.
Step 15
- Lift the leftmost flap seal up and remove the connector strip.
- Lift the two right flap seals up and remove the connector strip.
- Using tweezers or a spudger may be helpful.
Lift the leftmost flap seal up and remove the connector strip.
Lift the two right flap seals up and remove the connector strip.
Using tweezers or a spudger may be helpful.
Step 16
- Lift the fan component upward and away from the motherboard.
Lift the fan component upward and away from the motherboard.
To reassemble your device, follow steps 1-8 in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 6 other contributors
Angel L Appelzoller
Member since: 01/18/2022
223 Reputation
1 Guide authored
Badges:
10
+7 more badges
Team
Embry-Riddle Aeronautical University, Team 2-5, Rauch Spring 2022
Member of Embry-Riddle Aeronautical University, Team 2-5, Rauch Spring 2022
ERAU-RAUCH-S22S2G5
3 Members
2 Guides authored
