Difficulty
Easy
Steps
6
Time Required
10 minutes
Sections
1
- Bottom Panel
- 6 steps
Flags
Better Introduction
Improve this guide by completing or revising its introduction.
BackLenovo Yoga 910-13IKB
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
This has to be done to perform any maintenance or repairs on the device.
What you need
Step 1
Bottom Panel
- Before you begin, be sure to turn off your laptop and unplug it from the outlet.
- Turn the laptop over and remove the ten Torx T5 screws along the perimeter of the bottom panel.
- Remove the panel.
Before you begin, be sure to turn off your laptop and unplug it from the outlet.
Turn the laptop over and remove the ten Torx T5 screws along the perimeter of the bottom panel.
Remove the panel.
1024
Step 2
- Remove all 4 screws attached to the battery with a small Phillips head screwdriver.
- Each screw on the back is M2 x 1.7mm
- After the screws are taken out, remove the battery.
Remove all 4 screws attached to the battery with a small Phillips head screwdriver.
Each screw on the back is M2 x 1.7mm
After the screws are taken out, remove the battery.
Step 3
- Remove all 6 screws attached to the trackpad with a small Phillips head screwdriver.
- Each screw on the back is M2 x 1.7mm
- Detach the ribbon cable connected to the trackpad using a wedge device.
- Remove the trackpad using a wedge device
Remove all 6 screws attached to the trackpad with a small Phillips head screwdriver.
Detach the ribbon cable connected to the trackpad using a wedge device.
Remove the trackpad using a wedge device
Step 4
- Remove all 6 screws attached to the USB ports on both sides of the device with a small Philips head screwdriver.
- Detach both ribbon cables attached to each USB port with a wedge device, then detach the USB ports.
Remove all 6 screws attached to the USB ports on both sides of the device with a small Philips head screwdriver.
Detach both ribbon cables attached to each USB port with a wedge device, then detach the USB ports.
Step 5
- Remove all 4 screws attached to SSD stick with a small Phillips head screwdriver.
- Pull the SSD stick directly to the right until it shifts out of place to remove it.
- The storage chip above it (further away from you) may also simply be detached by pulling it directly to the right until it clicks out.
Remove all 4 screws attached to SSD stick with a small Phillips head screwdriver.
Pull the SSD stick directly to the right until it shifts out of place to remove it.
The storage chip above it (further away from you) may also simply be detached by pulling it directly to the right until it clicks out.
Step 6
- Remove all 4 screws attached to both fans, and the back connector strip (long metal piece furthest from you with screws in it) with a small Phillips head screwdriver
- Remove the back connector strip using a wedge device to pry it off of the device
- With the back connector strip removed, pry the fans (which are attached) using a wedge device and the fans will now be maintainable.
Remove all 4 screws attached to both fans, and the back connector strip (long metal piece furthest from you with screws in it) with a small Phillips head screwdriver
Remove the back connector strip using a wedge device to pry it off of the device
With the back connector strip removed, pry the fans (which are attached) using a wedge device and the fans will now be maintainable.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 5 other contributors
Kristen Gismondi
Member since: 11/12/2014
69,397 Reputation
176 Guides authored
Badges:
44
+41 more badges
Team
iFixit
Member of iFixit
Community
141 Members
15,769 Guides authored
