Difficulty

Easy

Steps

9

Time Required

                          4 - 5 minutes

Sections

3

  • Back Cover
  • 2 steps
  • Battery
  • 3 steps
  • Trackpad
  • 4 steps

Flags

0

  • BackLenovo Yoga 710-14IKB

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back Cover
  • Ensure your device is completely OFF before starting this guide.
  • Use a Torx T4 screwdriver to unscrew the nine 5 mm screws holding the cover in place.
  • Use a Torx T4 screwdriver to unscrew the 8 mm screw in the center.
  • When, reassembling, make sure not to tighten the screws too much or you may risk cracking the plastic cover.

Ensure your device is completely OFF before starting this guide.

Use a Torx T4 screwdriver to unscrew the nine 5 mm screws holding the cover in place.

Use a Torx T4 screwdriver to unscrew the 8 mm screw in the center.

When, reassembling, make sure not to tighten the screws too much or you may risk cracking the plastic cover.

1024

Step 2

  • Use the plastic opening tool to pry the cover up and away from the laptop, starting at one end and working your way around the cover.
  • The cover is large and flat and made of thin plastic. It cracks easily, so make sure not to pry too hard.

Use the plastic opening tool to pry the cover up and away from the laptop, starting at one end and working your way around the cover.

The cover is large and flat and made of thin plastic. It cracks easily, so make sure not to pry too hard.

Step 3

              Battery
  • Use a Phillips #00 screwdriver to remove the four 3 mm screws holding the battery in place.
  • Be careful not to cross-thread the screws. Also, don’t let the screws fall down into the laptop case.

Use a Phillips #00 screwdriver to remove the four 3 mm screws holding the battery in place.

Be careful not to cross-thread the screws. Also, don’t let the screws fall down into the laptop case.

Step 4

  • Use your fingers or an opening tool to slide the battery connector out of its motherboard socket.

Use your fingers or an opening tool to slide the battery connector out of its motherboard socket.

Step 5

  • Remove the battery.

Remove the battery.

Step 6

              Trackpad
  • Use the Phillips #1 screwdriver to take off the three 3mm screws.

Use the Phillips #1 screwdriver to take off the three 3mm screws.

Step 7

  • Grip the blue tab and pull out.
  • Careful to not pull too hard, there is a chance of damaging the tab.

Grip the blue tab and pull out.

Careful to not pull too hard, there is a chance of damaging the tab.

Step 8

  • Lift off the layer of tape from the trackpad.

Lift off the layer of tape from the trackpad.

Step 9

  • Push out the trackpad.

Push out the trackpad.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 2 other contributors 


                    Chuefeng Vang

Member since: 11/01/2018

136 Reputation

                                      1 Guide authored                  



                       Badges:
                       4







                                                        +1 more badge

Team

                       UMass Dartmouth, Team S5-G8, Gulbrandsen Fall 2018                        

                                                  Member of UMass Dartmouth, Team S5-G8, Gulbrandsen Fall 2018 



                    UMASSD-GULBRANDSEN-F18S5G8                     


                                            3 Members                     


                                            9 Guides authored