Difficulty
Moderate
Steps
9
Time Required
15 - 20 minutes
Sections
4
- Back Cover
- 2 steps
- Battery
- 3 steps
- SSD
- 2 steps
- Motherboard
- 2 steps
Flags
0
BackLenovo Yoga 710-14IKB
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Cover
- Ensure your device is completely OFF before starting this guide.
- Use a Torx T4 screwdriver to unscrew the nine 5 mm screws holding the cover in place.
- Use a Torx T4 screwdriver to unscrew the 8 mm screw in the center.
- When, reassembling, make sure not to tighten the screws too much or you may risk cracking the plastic cover.
Ensure your device is completely OFF before starting this guide.
Use a Torx T4 screwdriver to unscrew the nine 5 mm screws holding the cover in place.
Use a Torx T4 screwdriver to unscrew the 8 mm screw in the center.
When, reassembling, make sure not to tighten the screws too much or you may risk cracking the plastic cover.
1024
Step 2
- Use the plastic opening tool to pry the cover up and away from the laptop, starting at one end and working your way around the cover.
- The cover is large and flat and made of thin plastic. It cracks easily, so make sure not to pry too hard.
Use the plastic opening tool to pry the cover up and away from the laptop, starting at one end and working your way around the cover.
The cover is large and flat and made of thin plastic. It cracks easily, so make sure not to pry too hard.
Step 3
Battery
- Use a Phillips #00 screwdriver to remove the four 3 mm screws holding the battery in place.
- Be careful not to cross-thread the screws. Also, don’t let the screws fall down into the laptop case.
Use a Phillips #00 screwdriver to remove the four 3 mm screws holding the battery in place.
Be careful not to cross-thread the screws. Also, don’t let the screws fall down into the laptop case.
Step 4
- Use your fingers or an opening tool to slide the battery connector out of its motherboard socket.
Use your fingers or an opening tool to slide the battery connector out of its motherboard socket.
Step 5
- Remove the battery.
Remove the battery.
Step 6
SSD
- Use a Phillips #00 screwdriver to remove the 3mm screw on the SSD.
Use a Phillips #00 screwdriver to remove the 3mm screw on the SSD.
Step 7
- Use your fingers to lift up the SSD and pull away from the socket removing it from the laptop.
Use your fingers to lift up the SSD and pull away from the socket removing it from the laptop.
Step 8
Motherboard
- Use a PH00 screwdriver to remove the nine 3mm screws.
Use a PH00 screwdriver to remove the nine 3mm screws.
Step 9
- Disconnect the indicated cables from the motherboard.
- Be careful when removing cables. Do not pull or yank cables from their slots.
- Remove the motherboard.
- If you want to fully remove the motherboard, you must desolder the display cable.
Disconnect the indicated cables from the motherboard.
Be careful when removing cables. Do not pull or yank cables from their slots.
Remove the motherboard.
If you want to fully remove the motherboard, you must desolder the display cable.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
3 other people completed this guide.
Author
with 1 other contributor
Evan Cruzen
Member since: 11/01/2018
253 Reputation
2 Guides authored
Badges:
7
+4 more badges
Team
UMass Dartmouth, Team S5-G8, Gulbrandsen Fall 2018
Member of UMass Dartmouth, Team S5-G8, Gulbrandsen Fall 2018
UMASSD-GULBRANDSEN-F18S5G8
3 Members
9 Guides authored
