Difficulty

Moderate

Steps

8

Time Required

                          10 - 15 minutes

Sections

3

  • Back Cover
  • 2 steps
  • Battery
  • 3 steps
  • Headphone Jack
  • 3 steps

Flags

0

  • BackLenovo Yoga 710-14IKB

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back Cover
  • Ensure your device is completely OFF before starting this guide.
  • Use a Torx T4 screwdriver to unscrew the nine 5 mm screws holding the cover in place.
  • Use a Torx T4 screwdriver to unscrew the 8 mm screw in the center.
  • When, reassembling, make sure not to tighten the screws too much or you may risk cracking the plastic cover.

Ensure your device is completely OFF before starting this guide.

Use a Torx T4 screwdriver to unscrew the nine 5 mm screws holding the cover in place.

Use a Torx T4 screwdriver to unscrew the 8 mm screw in the center.

When, reassembling, make sure not to tighten the screws too much or you may risk cracking the plastic cover.

1024

Step 2

  • Use the plastic opening tool to pry the cover up and away from the laptop, starting at one end and working your way around the cover.
  • The cover is large and flat and made of thin plastic. It cracks easily, so make sure not to pry too hard.

Use the plastic opening tool to pry the cover up and away from the laptop, starting at one end and working your way around the cover.

The cover is large and flat and made of thin plastic. It cracks easily, so make sure not to pry too hard.

Step 3

              Battery
  • Use a Phillips #00 screwdriver to remove the four 3 mm screws holding the battery in place.
  • Be careful not to cross-thread the screws. Also, don’t let the screws fall down into the laptop case.

Use a Phillips #00 screwdriver to remove the four 3 mm screws holding the battery in place.

Be careful not to cross-thread the screws. Also, don’t let the screws fall down into the laptop case.

Step 4

  • Use your fingers or an opening tool to slide the battery connector out of its motherboard socket.

Use your fingers or an opening tool to slide the battery connector out of its motherboard socket.

Step 5

  • Remove the battery.

Remove the battery.

Step 6

              Headphone Jack
  • Remove the two 3mm screws from the headphone jack using a PH00 screwdriver.
  • Make sure not to strip the screws as they can sometimes be hard to remove.

Remove the two 3mm screws from the headphone jack using a PH00 screwdriver.

Make sure not to strip the screws as they can sometimes be hard to remove.

Step 7

  • Pop the black bar on the tip of the wire connected to the headphone jack circuitboard.
  • Disconnect the wire.
  • Be careful not to pull or yank the cable.

Pop the black bar on the tip of the wire connected to the headphone jack circuitboard.

Disconnect the wire.

Be careful not to pull or yank the cable.

Step 8

  • Remove the headphone jack circuitboard.

Remove the headphone jack circuitboard.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Evan Cruzen

Member since: 11/01/2018

253 Reputation

                                      2 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       UMass Dartmouth, Team S5-G8, Gulbrandsen Fall 2018                        

                                                  Member of UMass Dartmouth, Team S5-G8, Gulbrandsen Fall 2018 



                    UMASSD-GULBRANDSEN-F18S5G8                     


                                            3 Members                     


                                            9 Guides authored